Bedienungsanleitung Aiwa NSX-A10 (Seite 13 von 44) (Englisch, Französisch, Spanisch)

496477

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Within 4 seconds, select the duration

for the

timer-activated period with the W DOWN or WI

UP button.

The duration for the timer-activated period can be set between

5 and 240 minutes in 5-minute steps.

● If this step is not completed within 4 seconds, repeat from

step 1.

Prepare the source.

To listen to a CD, load the disc to be played first on tray 1.

To listen to a tape, insert the tape into deck 1 or 2.

TO listen to the radio, tune in to a station,

Press the POWER button to turn the unit off after

adjusting the volume and tone.

remains on the display after the power is turned off (timer

standby mode).

Get ready for the TAPE function or the timer

recording.

To listen to the tape, press the - button.

To record the source, press the

● button on deck 1.

When the timer-on time is reached, the unit turns on and

begins play with the selected source. While the timer is in

operation, the display indication is dimmer than usual.

The timer recording period and tape length

When the length of the tape to be recorded is shorter than the

timer recording period, the

● button on deck 1 is released before

the timer is off.

When the tape length is longer than the timer recording period,

the

● button is not released. If the ● is not released for a long

time, the tape in the deck may be damaged. Press the

■l=

button to release the

● button.

To cancel the timer standby mode temporarily

While pressing the SHIFT button, press the TIMER button so

that @ goes out in the display.

To restore the timer standby mode, press the TIMER button while

pressing the SHIFT button to display ~.

If using the unit after setting the timer

After setting the timer, you can use the unit. After using the unit,

check whether the contents in steps 5 and 6 are set as you wish,

turn off the power and set step 7 if necessary.

To change the specified time and function

Repeat all the steps again.

To check the specified contents

While pressing the SHIFT button, press the TIMER button. The

timer-on time is displayed for 4 seconds.

mia

SETTING THE SLEEP TIMER

The unit can be turned off automatically at a specified time.

Use the remote control.

Press the SLEEP button while pressing the SHIFT

button.

2 Within 4 seconds, press the ++ or B+ button

to specify the time until the power is turned off.

Each time the button is pressed, the time changes between 5

and 240 minutes in 5-minute steps.

‘ Specified time

While the timer is in operation, the display indication is dimmer

than usual.

To check the time remaining until the power is turned off

Press the SLEEP button once while pressing the SHIFT button.

The remaining time is displayed for

4 seconds.

To cancel the sleep timer

Press the SLEEP button twice while pressing the SHIFT button

so that “SLEEP on the display disappears.

. Timer playback and timer recording will not begin unless the

power is turned off.

● Connected equipment cannot be turned on and off by the built-

in timer of this unit. Use an external timer.

ENGL/W12

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aiwa NSX-A10 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info