Bedienungsanleitung Aiwa NSX-V8000 (Seite 6 von 76) (Englisch, Französisch, Spanisch)

496600

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

BEFORE OPERATION

SETTING THE CLOCK

-——._ __

—— .——_-

-———___ .._ ——— -

To turn the unit on

Press one of the function buttons (TAPE, TUNER, VIDEO/AUX,

CD).

Playback of the inserted disc or tape begins, or the previously

tuned station is received (Direct Play Function).

The POWER button is also available.

The disc compartment may open and close to reset the unit.

DEMO (Demonstration) mode

When the AC cord is connected for the first time, the display

window demonstrates the functions of the unit. When the power

is turned on, the DEMO display is overridden by the operation

display. When the power is turned off, the DEMO mode is

restored.

To cancel DEMO mode

Press the DEMO button. To reenter, press again.

Illumination guides

Whenever the AC cord is connected or one of the function buttons

is pressed, the buttons for that operation light up or flash.

Example: When the AC cord is connected, the II SET button

flashes as a guide to setting the current time.

Flash windows

The windows on the top of the unit and the cassette decks light

up or flash while the unit is being powered on.

To turn off the light of the top window, press the W button while

pressing the CD button. To turn back on, repeat the above.

To turn off the light of the cassette decks, press the E button

while pressing the TAPE button. To turn back on, repeat the

above.

After use

Press the POWER button to turn off the power. The display

changes to the clock.

1,3,5

■

2,4

When the AC cord is connected for the

button flashes.

first time, the II SET

Set the time as follows while the power is off.

Press the II SET button.

The hour flashes.

Press the 1<< DOWN or P->! UP button to

designate the hour.

Press the II SET button to set the hour.

The hour stops flashing and the minute starts flashing.

Press the 1<< DOWN or b+l UP button to

designate the minute.

Press the 11 SET button to set the minute and

complete setting.

The minute stops flashing on the display and the clock starts

from 00 second.

To correct the current time

Press the POWER button to turn the unit off. Press the II SET

button and carry out steps 1 to 5 above.

To display the current time

Press the CLOCK button on the remote control. The clock is

displayed for 4 seconds.

However, the time cannot be displayed during recording.

To switch to the 24-hour standard

Press the CLOCK button on the remote control and then press

the

❑ button within 4 seconds.

Repeat the same procedure to restore the 12-hour standard.

If the clock display flashes while the power is off

This is caused by a power interruption. The current time needs

to be reset.

If power is interrupted for more than approximately 24 hours, all

settings stored in memory after purchase need to be reset.

5 ENGLiSH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aiwa NSX-V8000 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info