Bedienungsanleitung Akai GX-400D (Seite 6 von 22) (Englisch)

752082

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

PLEASE READ TUE FOLLOWING PRECAUTIONS BEFORE OPERATION

* Your machine requires constan t voltage fOT optimum *Use good quality tape. New tape gives best results.

performance. Pie ase feier to voltage and cycle con- * Avoid using extremely thin tape whenever possible.

version procedure on page 13 if change of voltage or When the use of such tape is unavoidable, be sure to

cycles is necessary. depress the Stop Button before changing modes.

* As dirty heads and magnetized heads become the *As tapes which have not been used fOTaperiod of time

source of logs of sound, distortion, sound drop-out, may have become sticky, run tape once before using.

and other recording and playback failures, the heads *Always store tapes in a cool, dry place.

most be kept clean and demagnetized at all times.

* Place machine on a flat level surface. Operate in either

vertical or horizontal position.

*Do not place anything on top of the unit which will

obstruct the ventilator.

*If the sound sources are so rar away from the

microphones that the input level controls most be

tumed to maximum, some hum or noise will inevitably

be recorded.

A test recording is recommended before making a final

recording. .

'i~-"'.

.~I

'~I I/

I" I

....

Should there be a problem with your machine, write down

the model and serial numbers and all pertinent data

regarding warranty coverage as weIl as a clear description of

the existing trouble and contact your nearest authorized

Akai Service Station or the Service Department of Akai

Company, Tokyo, Japan.

UOW TO LOAD A MAGNETIC TAPE

I. PIace a full reel of tape on the supply reel table and an

empty reel on the take-np reel table.

2. Lock both reels into place by pulling tip of re el

retainers out ward and tuming to left or fight.

3. Unwind about a 85 cm length of tape from the supply

reel and thread the tape as shown by the dotted lines in

the figure.

4. Insert end of tape in slot of empty reel and wind

around reel hu b two or three times.

5. Continue winding tape onto take-np reel until all tape

slack hag been taken up.

When using 10-1/2" reels, place the standard accessory

reel adapter hubs on left and fight reel tables and lock into

place by pulling tip of reel retainers outward and tuming to

left or fight.

When using 10-1/2" metallic reels

Fit hubs over reel tables so that the white lIDes on the inner

and outer adapter hubs are aligned and match these lines

with dot on reel table (rubber bumpers of adapter will be

aligned with and rest on the rubber bumpers of the re el

table).

When using 10-1/2" plastic reels

Fit hubs over reel tables so that the white lines on the inner

and outer adapter hubs are aligned, hut do not match with

dot on reel table (rubber bumpers of adapter will enter

grooves between bumpers of reel table and vice-versa).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Akai GX-400D Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info