Bedienungsanleitung Akai MPC2500 (Seite 27 von 136) (Englisch)

630577

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

MPC2500 Operator’s Manual rev 1.0

Note repeat feature

If you press a pad while holding the [NOTE REPEAT]

key, the pad sound will be played repeatedly accord-

ing to the value of the timing correct until you release

the pad. You can also control its velocity by changing

the strength used to press the pad. With the Note re-

peat feature, you can record a difficult phrase to record

in real time, such as 16 beat hi hat, snare roll, etc…

01.

Press the [NOTE REPEAT] key during recording / playback.

02. While holding the [NOTE REPEAT] key, press the

pad to play repeatedly.

The pad’s sound will be played repeatedly accord-

ing to the value of the timing correct until you re-

lease the pad. You can also control its velocity by

changing the strength to press the pad.

While holding down the [NOTE REPEAT] key, the

bottom of display is changed as below. You can

change the Timing correct value directly with press-

ing the [F1] through [F6] key.

The selected Timing correct value is highlighted.

• Note Repeat Hold

You can also lock the “Note Repeat” feature by hold-

ing down the [NOTE REPEAT] key and then press-

ing the [SHIFT] key (or by holding down the

[SHIFT] key and then pressing the [NOTE REPEAT]

key). Pressing the [NOTE REPEAT] key again will

unlock the “Note Repeat” feature.

Punch In/Punch Out feature

You can start the recording in the middle of the sequence

during the playback (“Punch In”).

You can also stop the recording in the middle of the

sequence and resume the playback (“Punch Out”). This

is useful when you re-record the part of the recorded

sequence.

Punch In

Press the [PLAY], or the [PLAY START] key to play

back a sequence. At the point where you wish to start

the recording, press the [REC] key while holding the

[PLAY] key. The MPC2500 will start the recording.

If you press the [OVER DUB] key and the [PLAY]

key instead, the MPC2500 will start the over dubbing.

Punch Out

If you press the [REC], or the [OVER DUB] key dur-

ing the recording/overdubbing, the MPC2500 will stop

the recording/overdubbing and resume the playback.

Auto Locate feature

The [GO TO] key is used to move to a specific position

within a sequence. You can memorize up to three lo-

cate points.

• Saving a Locate point

01. In the MAIN page, press the [GO TO] key while the

sequence is stopped.

The Locate window will open up.

In the Go to field, the now time in the MAIN page

is displayed. You can enter the locate point you wish

to save by using the numeric keys or the DATA

wheel.

02. Move the cursor to either Locate1 – Locate 3 field

and press the [F2] (CAPTUR) key.

• Locating to a saved Locate point

01. In the MAIN page, press the [GO TO] key while the

sequence is stopped.

The Locate window will open up.

02. Move the cursor to either Locate 1 – Locate 3 field

and press the [F5] (GO TO) key.

The Now Time instantly change to the saved Lo-

cate point.

Tips: You can use the Auto Locate feature in both the MAIN

page and in the STEP/GRID mode.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Akai MPC2500 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Akai MPC2500

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info