Bedienungsanleitung Akai MPC2500 (Seite 73 von 136) (Englisch)

630577

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

MPC2500 Operator’s Manual rev 1.0

Chapter 12 : Editing a sample

Setting the start / end points for the sample

The start/end points sets the part of the sample data, which will actually be played back. The recorded sample may have an

unnecessary part at the beginning, which may make it more difficult to place the sound in the correct spot timing when

hitting the pad. You can fix this problem by adjusting the start point. You can also adjust both the start and end points to play

only a part of the phrase. If the sample has empty parts at the end, which consumes unnecessary memory, you can delete the

empty parts by adjusting the end point and using the edit feature.

Start/end points are displayed in sample points. The sample point is the minimum unit used for sample editing. The MPC2500

has the 44100 sample points per second.

About the waveform display

The TRIM page displays the waveform of the sample selected in the Sample field.

It displays the waveform of the whole sample, with

the parts set by start/end points highlighted. If you

select a stereo sample, you can select the channel

(LEFT/RIGHT) to display in the View field.

Adjusting the start point

01. Press the [MODE] key and then the [PAD 6] (TRIM).

When you press the [MODE] key, its LED will blink. Press the [PAD 6] while the [MODE] key’s LED is blinking to

display the TRIM page.

02. Select the Sample field and select a sample you wish to edit.

The Sample field is located in the upper left corner of the screen, which displays the sample name. It displays the

waveform of the selected sample.

03. Select the St (start) field and adjust the start point.

You can change the start point by turning the DATA wheel.

If you press the left/right cursor key while holding the [SHIFT] key, you can select the digit with the DATA wheel.

You can also enter the value directly with using the numeric keys.

04. Hit the pad to check the start point.

When you hit the pad, the MPC2500 plays the sample. The playback method varies depending on the pad.

If you hit the [PAD 14] (PLAY TO), the MPC2500 will play the sample before the start point.

If you hit the [PAD 15] (PLAY FROM), the MPC2500 will play the sample from the start point.

If you hit the [PAD 16] (PLAY ALL), the MPC2500 will play the whole sample regardless of the start/end point settings.

If you hit any pad from the [PAD 1] to [PAD 12], the MPC2500 will play from the start point to the end point.

Adjusting the end point

05. Select the End field and adjust the end point.

You can change the end point by turning the DATA wheel.

If you press the left/right cursor key while holding the [SHIFT] key, you can select the digit with the DATA wheel.

You can also enter the value directly with using the numeric keys.

In this section, you will learn about the TRIM mode, where you can set the sample’s start/end points, or the loop.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Akai MPC2500 Seite 73

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Akai MPC2500

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info