Bedienungsanleitung Akai MPC2500 (Seite 74 von 136) (Englisch)

630577

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

MPC2500 Operator’s Manual rev 1.0

Chapter 12: Editing a sample

06. Hit the pad to check the end point.

When you hit the pad, the MPC2500 plays the sample. The playback method varies depending on the pad.

If you hit the [PAD 14] (PLAY TO), the MPC2500 will play the sample until the end point.

If you hit the [PAD 15] (PLAY FROM), the MPC2500 will play the sample from the end point.

If you hit the [PAD 16] (PLAY ALL), the MPC2500 will play the whole sample regardless of the start/end point settings.

If you hit any pad from the [PAD 1] to [PAD 12], the MPC2500 will play from the start point to the end point.

Zooming in/out of the waveform

With the Fine window, you can zoom in to a part of the

waveform and edit the part in details. Press the [WIN-

DOW] key in the TRIM page, when the cursor is either

in the St (Start) or End field, and the Fine window will

be displayed.

In the Fine windows, the waveform display varies de-

pending on the location of the cursor. When you select

the St (Start) field with the cursor, it displays the start

point in the center of the window. When you select the

end field, it displays the end point in the center.

If you press the [F2] (ZOOM-) key the waveform will

be zoomed out, if you press the [F3] (ZOOM+) key, it

will be zoomed in.

LINEAR and LOGARITHMIC displays

The vertical axis indicates the sample’s level. Normally,

the waveform display is set to LINEAR, which displays

the sample level as it is. However, some parts (fade out

part etc…) may not be displayed in the waveform if

the level is too low. In this case, you can switch to the

LOG (logarithmic) display by pressing the [F5] (LOG)

key and you can see the parts whose level is low. When

you switch to the LOG mode, the display in the [F5]

key will change to LINEAR. To switch back to the LIN-

EAR mode, press the [F5] key again.

Deleting an unnecessary part

from a sample (DISCARD)

The MPC2500 plays back only the part of the sample from the

start point to the end point. The parts outside these points are

not used for the playback. With the Discard function, you can

delete these unnecessary parts and save the memory space.

01. Adjust the start/end points.

Set the points so that the MPC2500 plays back only

the necessary part.

02. Press the [F6] (EDIT) key.

The Sample Edit window will be displayed.

03. In the Edit field, select DISCARD.

04. Press the [F5] (DO IT) key.

The data outside the start/end points will be de-

leted. The deleted data will be returned to the avail-

able memory.

Deleting a selected range from

sample and moving the data after

the end point towards the start point.

(DELETE)

01. Adjust the start/end points.

Set the range so that you wish to delete with the

start/end point.

02. Press the [F6] (EDIT) key.

The Sample Edit window will be displayed.

03. In the Edit field, select DELETE.

04. Press the [F5] (DO IT) key

The Keep or Retry window will be displayed.

New name field :

Set the name for the new sample

[F2] (PLAY) :

You can audition the new sample.

[F3] (OVER W) : You can delete the original

sample and keep the new

sample by pressing this key.

The sample name remains.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Akai MPC2500 Seite 74

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Akai MPC2500

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info