Bedienungsanleitung Akai MPC2500 (Seite 94 von 136) (Englisch)

630577

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

MPC2500 Operator’s Manual rev 1.0

84 Chapter 13: PROGRAM

Editing the sound of a sample

Each pad has a parameter to change the sound, which is

called “Filter”. You can edit the sound of the sample by ed-

iting this parameter. This is done in the FILTER page of the

PROGRAM mode.

Each pad has two filters. You can create a more complicated

sound by combining these two filters. Also you can link these

two filters to make a more powerful filter.

Setting the Filter

01.

In the PROGRAM mode, press the [F2] (FILTER) key.

The FILTER page will be displayed. You can select

the program to edit in the Pgm field.

02.

Select the pad you wish to edit for the sound by hitting it.

The Pad field displays the pad number of the se-

lected pad. To the right of the pad number, the name

of the sample assigned to the pad is displayed.

03. Select the Type field of filter 1 (to the left) and select

which filter type to use.

The MPC2500 has several types of filter to edit the

sound. With these filters, you can cut or boost the

specific frequency of the sound.

LOW PASS

This filter cuts out the high fre-

quencies and passes the low fre-

quencies. This filter is frequently

used in the electronic instru-

ments such as synthesizers.

HIGH PASS This filter cuts out the low fre-

quencies and passes the high

frequencies.

BAND PASS The filter passes the specific fre-

quencies and cuts out the other

frequencies.

OFF No filter is used.

04. Select the Freq field and set the cut off frequency.

The cut off frequency is the frequency that triggers

the filter. When you select the LOW PASS filter, if

you set the cut off frequency too low, the sound

will seem dull. This is because most of the higher

frequencies of sound are cut off by the filter. When

you select the HIGH PASS filter, if you set the cut

off frequency too high, most of the lower frequen-

cies are cut off, which results in a more hollow

sound.

05.

Set the Reso field to adjust the resonance of the filter.

If you set the resonance value at a larger value, the

frequencies set in the Freq field will be boosted

more. It is hard to describe the effect of the reso-

nance, because it differs depending on the cut off

frequency and filter type. Experiment several set-

tings in the Type field, Freq field, and Reso field.

Note : If you notice distorted sound while using the FILTER,

you can use the Att parameter to adjust the level of the signal

sent to the filter, and remove the unwanted distortion.

06.

Set the filter of the filter 2 (to the right) in the same way.

Tips : You do not have to edit both filter 1 and 2. If you do not

need the filter, set the Type field to OFF.

Linking the two filters

You can link the two filers to make it as one powerful filter.

To link the filters, select the LINK in the Type field for

the filter 2 (in the right).

The MPC2500 will ignore the settings in the Freq field

and the Reso field for the filter 2 and apply the same

setting as those for the filter 1, which provides you with

a powerful filter effect.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Akai MPC2500 Seite 94

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Akai MPC2500

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info