Bedienungsanleitung Al-ko AL-KO 137 SB (Seite 34 von 124) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

594592

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

Using your brushcutter

ENGLISH 14

7. Using your brushcutter

7.1 Scope of Application

Only use brushcutters fitted with the 3-tooth brush

cutting blade for mowing grass, light brush, reeds

and uncultivated growth at ground level.

Never use the brushcutter for any other purpose.

Using the cutting tools, which are available as

accessories and which are specified for certain

tasks, enable the brushcutter to be used for those

purposes specifically mentioned in the accessory

instructions. Also observe the safety instructions in

those accessory instructions.

Generally, use only the cutting tools authorised for

use with this brushcutter. Always fit the contact

shield specified for this brushcutter and cutting tool. If

in doubt, contact your local SOLO dealer.

7.2 Initial use/ start-up behaviour

When switching on the engine for the first five times

prior to commencing work, first operate for a short

time in the mid-speed range without any load until

the engine has warmed up a little.

7.3 Correct brushcutter operation

Observe the relevant safety instructions when using

the brushcutter.

The rotational direction of the cutting tool makes the

operation on the l.h. side of the cutting tool (from the

operator's viewpoint, subject to the brushcutter being

held correctly – section A) particularly free from

kicking. Therefore, always approach the area to be

cut from the right. This brings the l.h. side of the

cutting tool into contact with the material to be

trimmed first. Particularly when cutting tougher

growth (such as medium sized weeds and wild

growth), ensure that you do not "stab" the front of the

brushcutter into the material to be trimmed.

Approach the working area with the brushcutter set to

idle, and then switch to full throttle. Never leave the

engine running at high speed without applying a load.

Dip the tool from the r.h. side 2/3 into the material to

be trimmed. Then work the brushcutter lie a scythe,

i.e. by moving forward step by step, whilst cutting

from right to left.

Operate the brushcutter at full throttle to obtain an

optimum cutting result. Never operate with the clutch

in slipping range. Consequential damage through

excess loads or overheating is excluded from our

warranty.

Immediately stop the engine in case of noticeable

vibrations or when material has gathered around the

cutting tool or contact shield. Slow down the cutting

tool by pressing it onto the ground, until it has come

to a complete standstill. Pull the spark plug cap from

the plug, and clean the tool seat of all grass, roots

etc. Check the entire brushcutter for perfect condition.

7.4 Sharpening instruction for brush blade

When dull, the

cutter blade’s

edges can be

re-sharpened

on both sides

with a flat file

at an angle

of 30°.

All cutting edges need to be filed back equally, if the

wear and tear is substantial, or if there are broken-off

cutting edges. It is necessary to check for imbalance

and if necessary, to make corrections by additional

filing. The sharpening angle is 30°.

Fig. 14

Fig. 15

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Al-ko AL-KO 137 SB Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info