Bedienungsanleitung Al-ko AL-KO 142 (Seite 31 von 124) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

594600

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

Preparing the equipment for use

ENGLISH 11

C) Installation of the nylon line head (available as

an accessory)

The following components should be removed when

converting the brushcutter from the 3-tooth brush

cutting blade to a nylon line head (see Fig. 5):

Retaining nut (28) (caution: left-handed thread), nut

protector (27), pressure washer (26) and metal

cutting blade.

• Fit the anti-winding protection (30) (supplied with

the line head) after the pressure piece (25). The

smooth side of the anti-winding protection faces

the gearbox, with the edge of the anti-winding

protection covering the edge of the angular

gearbox.

• Block the shaft with the pin (29).

• Screw on the line head by hand. Caution: left-

handed thread.

• Fit the protective bar (31) with assembled line

trimmer from underneath onto the guard. Bend

the protective bar slightly in the process.

Important: When using the line head, never start the

brushcutter without the protective bar and the line

trimmer assembled.

If the length of the line has been adjusted (see

chapter 8.5, "Adjusting the cutting line"), the line

trimmer will automatically cut the ends of the line to

the correct length during operation.

When using metal cutting blades, always work

without the protective bar fitted.

C) Assembly of the "Jet-Fit " cutting head

Insert the cutting line

into the main body of

the cutting head in

accordance with the

arrows on the main

body. Insert enough

line so that approx. 20

mm of the cutting line

protrudes from the

opening on the

opposite side.

Make sure that the

cutting teeth are

correctly aligned in the

direction of rotation.

Various washers are

supplied with the

cutting head.

For installation on this

type of brushcutter, use

exactly the washer

dimensions shown in

the illustration (outer

diameter, inner

diameter).

Block the shaft with the pin (29) and tighten the nut

(28). Check that the cutting head is securely seated

and properly centred.

Fit the cover of the

cutting head in place,

turn it in the direction of

the arrow and tighten it

with the combination

wrench as shown in the

illustration until it

engages.

When using the "Jet-Fit" cutting head, always use the

standard guard and the assembled protective bar.

Cutting lines must not touch the guard during rotation.

If necessary, insert the cutting lines slightly further

into the main body of the cutting head. The line

trimmer which is assembled in the protective bar is

not suitable for cutting lines.  The length of the

cutting lines needs to be manually adjusted to the

correct length.

To replace a cutting

line, pull the

protruding end back

out from the main

body in the direction

of the arrow (use

universal pliers if

necessary).

Fig. 8

Fig. 9b

Fig. 9d

Fig. 9e

Fig. 9a

Fig. 9c

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Al-ko AL-KO 142 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info