Bedienungsanleitung Al-ko AL-KO BC 4535 II-S Premium (Seite 17 von 260) (Alle Sprachen)

594329

Zoom out

Zoom in

Vorherige Seite

1/260

Nächste Seite

Safety instructions

440 247_a 17

Before leaving the equipment unattended:

Turn the engine off

Wait for the cutting unit to stop

Do not leave the appliance unsupervised.

Children and other persons who are unfami-

liar with the operating instructions must not

operate the machine

Before use, check that all screws, bolts and

nuts on the device are tight.

Insert the blade guard for ever, before they

transport the device or the knife or store.

ASSEMBLY

CAUTION!

The machine must not be put in opera-

tion before it has been assembled com-

pletely.

Mounting the “Bike” grip

see Figure 2

1. Place the rubber sleeve (3) over the shaft.

2. Fasten the lower brace (2) and the center

piece (4) using the four Allen screws (1).

3. Place the grip rod (5) into the grip holder and

fasten with the upper brace (6) and the four

Allen screws (7).

Mounting the guard

see Figure 3

1. Place the metal plate (2) under the guard (3).

2. Fasten to the support bar with 4 screws (1).

ADVICE

The cutter integrated into the guard au-

tomatically shortens the cutting string to

the optimal length.

Mounting the rail

see fig. 14

1. Slide the lower half of the rail into the holder.

2. Engage the button.

3. Tighten the holder.

Mounting the rail

see fig. 11

1. Release the lock nut (a -1) and pull out the

splint (a -2) slightly.

2. Insert the lower rail with the protective cover

(a -3) in the upper rail.

➯

Insert guide groove on the splint side.

3. Release the splint again (b -1) and secure the

lower rail with the lock nut (b -2).

Detaching the rail

see fig. 11

1. Release the lock nut (c -1) and pull out the

splint (c -2) slightly.

2. Pull the lower rail with the protective cover (d

-1) out of the upper rail.

➯

The Motorsense is now more compact

for storage.

Mounting the cutting blade

see Figure 4

1. Remove the smaller half shield from the

guard.

2. Remove the cotter pin (8) and flange (5).

3. Place the cutting blade (4) on the drive plate

(2) in such a way that the hole in the cutting

blade is exactly aligned with the guide circle

of the drive plate.

4. Push the flange (5) onto the cutting blade so

that the flat side faces the cutting blade.

5. Secure the clamping nut (7) on the guide pin

(1). To do this, insert the Allen key (3) into the

hole provided and tighten.

➯

Caution: left-hand thread!

6. Secure the nut with the cotter pin.

Mounting the string head

see Figure 5

1. Remove the cotter pin and flange.

2. Insert an Allen key (3) into the hole in the drive

plate (2) and screw the string head (4) onto

the guide pin of the drive shaft (1).

➯

Caution: left-hand thread!

3. Lock the drive plate with the Allen key in order

to mount the string head.

Adjusting the shoulder strap

see Figure 10

1. Push the shoulder strap first over the left

shoulder.

2. Hook the locking hooks into the eyelet.

3. Check the length of the shoulder strap by ma-

king a number of swinging movements wi-

thout switching on the engine.

The string head or cutting blade must

move parallel to the ground.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Al-ko AL-KO BC 4535 II-S Premium Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info