Bedienungsanleitung Al-ko JET 4000 (Seite 15 von 172) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Türkisch, Schwedisch, Finnisch)

601990

Zoom out

Zoom in

Vorherige Seite

1/172

Nächste Seite

Startup

467 774_a 15

3. Fix a pressure line (Fig. B -12) to the elbow

nipple (Fig. B -13).

4. Open all closing off devices (valves, spray

nozzles, water cock) in the pressure line.

STARTUP

Filling the garden pump

CAUTION!

Dry running will destroy the pump! The

pump must be filled with water up to the

overflow before each use so that it can

draw water immediately.

1. Open the filling screw (Fig. A -2) with the filter

key.

2. Fill with water via the filling screw until the

marl on the pump housing is reached.

3. Screw the filling screw back in position.

ADVICE

In order to reduce the suction time, fill the

suction hose with water before screwing

in position.

Switch the pump on

1. Open all closing off devices (valve, spray

nozzle, water cock) in the pressure line.

2. Insert the mains plug on the connection cable

into the plug socket.

3. Switch the garden pump on at the on / off

switch.

CAUTION!

Do not allow the pump to run against a

closed off pressure line.

Switch pump off

1. Switch the garden pump off at the on / off

switch after use.

2. Close all the closing off devices in the pres-

sure line.

ADVICE

If nothing is drawn up for longer than

180 seconds, the garden pump automa-

tically switches to "Fault" and turns off.

CAUTION!

Danger of injury from hot water

In extended use against the closed pres-

sure side (>10 min.), the water in the

pump can be severely heated up and can

be emitted in an uncontrolled manner!

Isolate the unit from the mains and allow

the pump and water to cool down. Start

the unit again only after all the faults have

been rectified!

The risk of injury from hot water can arise if:

the installation is not correct

the pressure side is closed off

there is a lack of water in the suction line, or if

the pressure switch is defective.

Procedure

1. Isolate the unit from the mains and allow the

pump and water to cool down.

2. Check the unit, the installation and water le-

vel.

3. Start the unit again only after all the faults

have been rectified!

MAINTENANCE AND CARE

CAUTION!

The pump must be isolated from the

mains before any maintenance and ser-

vice work. Remove the mains plug from

the plug socket.

Clean the filter

1. Drain screw filter chamber (Fig. A -10) un-

screw the draining opening, drain the fil-

ter chamber and close the draining opening

again.

2. Unscrew clear sight cover filter (Fig. A -9)

using the filter key (Fig. C -18/D) .

3. Remove filter (Fig. C -20) from the filter hou-

sing and clean under flowing water.

4. Clean the filter housing and clear sight cover

of the filter.

5. Before fitting the filter, check the filter seals

(Fig. C -19) and the housing seal (Fig. C -23)

and replace if necessary.

6. Fit the filter, screw the clear sight cover in

place and tighten hand-tight with the filter key.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Al-ko JET 4000 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info