Bedienungsanleitung Al-ko TWIN 11000-14000 (Seite 16 von 156) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

601636

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

Assembly

16 SUB 10000-13000 DS / TWIN 11000-14000

ASSEMBLY

Mounting the pressure line

TWIN pumps

see Fig. A

1. Screw the connection elbow (7) into the pump

outlet.

2. Screw the combination nipple (4) onto the

connection elbow.

3. Fix a hose to the combination nipple.

SUB pumps

see Fig. C

1. Screw the combination nipple (4) onto the

connection elbow.

2. Fix a hose to the combination nipple.

ADVICE

The combination nipple can be trimmed

to suit the selected hose connection. Use

the largest possible hose diameter.

Setting the adjustable foot

see Fig. E

TWIN pumps

1. Turn the adjustable foot (6) to the right.

➯

The adjustable foot disengages.

2. Set the adjustable foot to position "O" or "U".

3. Turn the adjustable foot (6) to the left.

➯

The adjustable foot locks back in posi-

tion.

SUB pumps

1. Turn the adjustable foot 90° to the left to move

the adjustable foot to the top position.

2. Turn the adjustable foot 90° to the right to

move the adjustable foot to the bottom posi-

tion.

ADVICE

The combination nipple can be trimmed

to suit the selected hose connection. Use

the largest possible hose diameter.

STARTUP

Safety

CAUTION!

Exclude, by suitable means, that, in the

event of a fault in the immersion pump,

consequential damage is caused by floo-

ding.

Make sure that the immersion pump is stan-

ding securely or operate the immersion pump

suspended from a rope.

Make sure there is adequate clearance under

the pump.

Never allow the immersion pump to run

against a closed off pressure line.

When using in shafts, make sure the size is

adequate.

Always cover the shaft with a secure foot-

plate.

Switching the pump on

see Fig. A - C

CAUTION!

The immersion pump must not draw in

any solid bodies. Sand and other abra-

sive materials in the conveying medium

will destroy the immersion pump.

1. Unwind the connection cable (1) completely.

2. Make sure that the electrical plug connection

is mounted in the area safe from flooding.

Models with float switch

3. Change the terminal position and adjust the

switching points of the float switch(10) indivi-

dually.

4. Attach the cable on the float switch to the

pump housing(4)securely.

➯

Recommended cable length on the float

switch approx. 100 mm

Models with level switch

5. Slide the level switch (8) to the relevant height

and thus set the switching points.

ADVICE

Use a suitable plate to ensure se-

cure mounting of the immersion

pump on muddy, sandy or stony

ground.

6. Immerse the immersion pump in the convey-

ing medium slowly. Hold the immersion pump

at a slight angle to allow any air to escape.

7. Insert the mains plug into the plug socket.

➯

The immersion pump switches on auto-

matically using the float switch when a

specific water level has been reached,

and switches off again if the water drops

below the switch-off height.

Switching the pump off

1 Remove the mains plug from the plug socket.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Al-ko TWIN 11000-14000 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info