Bedienungsanleitung Al-ko TWIN 11000-14000 (Seite 17 von 156) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

601636

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

Startup

467 772_a 17

Automatic mode

1. In automatic mode, set the adjustable foot to

position "U" (bottom) to achieve the greatest

possible feed rate.

2. Insert the mains plug into the plug socket.

Models with float switch

3. Switch the operation selection switch on the

mains switch to "AUTO" (Fig. G).

Models with level switch

4. Slide the level switch upwards to the desired

switch-on height (Fig. I).

➯

The pump switches on automatically at a

specific water level (switch-on height) by

the float switch and when the water level

falls to the switch-off height it switches off

again, see technical data Page 5

Manual operation mode

In manual mode, the water can be pumped away

to a very low level of residual water.

Minimum water level for commissioning: see tech-

nical data.

Pumping out to residual water level

CAUTION!

Monitor the pump continuously when

pumping out to the residual water level

and avoid the pump running dry. Shut

the pump down when the residual wa-

ter level has been reached by switching

the operation mode selector switch to

"AUTO". The pumps switch on again au-

tomatically when the switch-on height is

reached.

Set the adjustable foot to the "O" (top) position for

pumping out to the residual water level:

1. Remove the mains plug from the plug socket.

Models with float switch

2. Switch the operation selection switch on the

mains switch to "MAN" (Fig. G). The pump

switches on and starts to feed.

Models with level switch

3. Slide the level switch upwards to the "MAN"

position (Fig. I).

ADVICE

If the water drops below the residual wa-

ter level, the pump will draw air in. In this

case, the pump must be vented when

the water level rises and before using it

again.

MAINTENANCE AND CARE

Cleaning the pump

ADVICE

After conveying chlorine-containing

swimming pool water or fluids that leave

a residue, the pump must be flushed out

with clear water.

1. Clean the suction slots on the suction foot if

necessary with clear water.

Removing/fitting the level switch

see Fig. H

1. Unscrew the fixing screw(2) and then first tip

the housing float switch(1) upwards and then

tilt to the front.

2. Clean the float body (4) and guides (3).

3. Place the float body back in the guide.

4. Replace the housing float body and push

downwards.

5. Screw the fixing screw in.

Removing/fitting the adjustable foot

TWIN pumps

see Fig. F

1. Unscrew the engaging screws (7) and pull the

adjustable foot (6) out of the pump housing

(8).

2. Clean the adjustable foot and the pump hou-

sing.

3. Insert the adjustable foot in the pump housing,

align and screw the engaging screws back in

place.

STORAGE

ADVICE

In the event of a risk of frost, the system

must be drained completely.

DISPOSAL

Do not dispose of old

equipment,batteries or accumulators

as householdwaste!

Product, packaging, and accessories

were made with recyclable materials, and

should be disposed of accordingly.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Al-ko TWIN 11000-14000 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info