Bedienungsanleitung Alde Comfort 2928 (Seite 16 von 32) (Deutsch, Englisch, Holländisch, Französisch, Schwedisch, Finnisch)

626264

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

for any length of time without its quality deteriorating.

LPG is entirely free of poisonous substances.

The risk with gas is that leaking gas is ignited, resulting

in an explosion. As LPG has no distinct aroma, sulphur

compounds are added that give a distinct, pungent

smell, even when the concentration of gas is as low as

one fth of the lower explosion limit. The LPG burner

usually works at a lower pressure than the pressure in

the cylinder. Low pressure is obtained by allowing the

LPG to pass through a regulator.

TROUBLESHOOTING7.

Here is a brief troubleshooting chart that may be of

help in the event of simple faults.

The ignition spark comes but the boiler does

not start

Check gas supply.1.

Is the service tap fully open?2.

If the boiler has been out of use for a while or if the 3.

gas cylinder has been changed, it takes longer to

ignite than normal.

The thermostat knob must be pushed down as far 4.

as it will go when starting.

If this does not help, contact your service workshop.5.

No ignition spark

Check that there is a 12-volt supply to the boiler.1.

Check the fuse on the boiler is intact.2.

Check that the warning light for the ignition spark is 3.

ashing.

Remove the lower front cover. Check that the ca-4.

bles to the ignition transformer (small black box just

under the control panel) and the microswitch (under

the thermostat) are properly attached and that there

is no corrosion on the cable clips.

If this does not help, contact your service workshop.5.

The boiler ignites but goes out when the ther-

mostat knob is released

Repeat the ignition procedure as per instructions 1.

in chapter 2:2 (wait 3 minutes before igniting the

boiler again). Make sure that the thermostat knob is

pushed down as far as it will go and hold it in posi-

tion for 20-30 seconds after the warning light has

gone out.

Check that the pilot ame comes into contact with 2.

the tip of the thermoelement (to the right of the pilot

burner).

If this does not help, contact your service workshop.3.

The boiler boils

Turn the thermostat knob to 1 (lowest system tem-1.

perature) and check that the main ame goes out,

as it should.

Check that the sensor is secured correctly. It should 2.

be attached to the body of the boiler by a spring

clip just under the control box with heat-conducting

putty in between.

If this does not help, contact your service workshop.3.

Vibrations in the circulation pump (12volt)

Release the nut holding the circulation pump.1.

Turn the pump a little and tighten up the nut again.2.

Check that the rubber connection between the 3.

motor and the shaft is straight and does not wobble

when in motion.

Check that there is no obstruction in the way of the 4.

pump at the bottom of the expansion vessel.

If this does not help, contact your service 5.

workshop.

Noise in the motor of the circulation pump

(12volt)

Drop a drop of sewing machine oil into the centre 1.

hole at the top of the motor.

If the noise does not disappear or returns after a 2.

while, the motor should be replaced.

Circulation pump (12volt) will not start

Check that the slider on the room thermostat is in 1.

”ON” position.

Check that the temperature shown on the room 2.

thermostat is higher than inside the vehicle.

Check that the changeover switch on the control 3.

panel for the circulation pump is on ”12-volt pump”.

Remove the circulation pump and check that the 4.

cables are properly secured, and that there is a 12-

volt supply.

If this does not help, contact your service 5.

workshop.

Incorrect temperature on the room thermostat

Check by using an accurate thermometer inside the 1.

vehicle.

Remove the cover from the room thermostat (press 2.

in the pin on the left-hand side and pull the cover

straight out).

Pull out the knob and move it as many degrees up 3.

or down as it indicated wrongly, and press it into

place again.

Replace the cover and check that the temperature 4.

agrees with the scale on the room thermostat.

The immersion heater has stopped working

Check that there is power (230/240 volts) in the 1.

wall socket.

Check that the relays on the immersion heater 2.

switch on (a gentle click should be heard).

Check whether the overheating protection has trig-3.

gered. If so, press in the button on the side of the

cover.

If this does not help, contact the service workshop.4.

Insufcient hot water

Check that boiler thermostat is set on maximum 1.

position.

GUARANTEE8.

Alde International’s guarantee applies for one year

from date of delivery and covers material defects and

manufacturing defects only, on condition that above

instructions have been adhered to.

NB. Use only original parts from Alde as spares.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alde Comfort 2928 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Alde Comfort 2928

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info