Bedienungsanleitung Alecto BW-600 (Seite 30 von 46) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

803285

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

Fast warming:

1. Always place the basket into the bottle warmer rst before adding a bottle. Do never place

the bottle directly onto the heating element.

2. Fill the bottle warmer with water until the level of the milk in the bottle. Regardless of the

amount of milk, the water should not exceed the MAX level, indicated in the inner rim. It is

recommended to use distilled water, in connection with possible scale formation.

3. Turn the knob to select the function. The power light is on. See the fast warming chart to

check how long the milk needs to be warmed.

Note: The speed of warming milk depends on the amount of the milk warmed and on it's

initial temperature like room temperature (20°C) or fridge temperature (4°C).

4. Note there is no timer on the BW600BK. So count the time yourself and remove the bottle

from the bottle warmer after the indicated time has run out.

5. Gently shake the bottle or milk storage basket and check the temperature before you are

feeding the baby. Check the temperature by sprinkling a few drops on the inside of your wrist.

Tip: When you nd the milk is not warm enough, place the bottle back into the basket for

maximum 0,5 min/1 min for extra warming. (Fill a small amount of water into the bottle

warmer when the water has dried out and then restart). This will cause a slightly warmer

result but without overheating.

Caution: If you leave the bottle into the bottle warmer longer than the indicated time on

the chart, the milk may become overheated. Cool the milk before feeding.

Note: If you use overheated breast milk, valuable nutrients and vitamins may be lost.

6. When the warming is completed, turn the knob to OFF.

Caution: The water in the bottle warmer may be hot after nishing the fast warming.

Be carefull the water can causes serious burns. If you do not turn the knob into to OFF

function, the water keeps heating up and will reach a very high temperature.

7. If the water has dried out, the reset switch will be triggered to shut off the power. Wait

10 minutes to cool down and then press the reset switch (until you hear a clicking sound)

restart the warming.

8. Before warming up a second bottle, it is best to wait 10 minutes for the bottle warmer to cool

to prevent overheating or pour cold water into the bottle warmer.

Recommended fast warming time (minutes)

Milk volume

Bottle Temp. 60 ml 120 ml 180 ml 240 ml

Glass 4°C 3 min 4 min 5 min 6 min

20°C 2 min 3 min 3,5 min 4 min

Plastic 4°C 4 min 5,5 min 6 min 6,5 min

20°C 3 min 4 min 4,5 min 5 min

NOTE: These times are approximate and depend on the material of the bottle, the exact starting

temperature of the milk, the amount of milk and the amount of water. Use these times as a guide

only.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alecto BW-600 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info