Bedienungsanleitung Alecto DVM 50 (Seite 31 von 36) (Deutsch, Englisch, Holländisch, Französisch)

803225

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Select a camera:

1. Press 4x on the button.

2. Press the

and

keys to select the camera.

A ‘ ‘ behind the camera number will indicate that a camera is logged in.

The ‘scan’ function allows the parent unit to show every camera for 10 seconds; note, if

the camera is switched off or out of range, the out of range picture will be shown and the

out of range beep tones will sound.

3. Press 1x on the button to save the setting and exit the menu.

See chapter 5 on how to add additional cameras.

4.4 AUTOMATIC NIGHT VISION:

The baby unit has 6 built in infrared LEDs; These LEDs will automatically turn on when the baby unit

detects darkness and turn off again when it gets light.

These LEDs can illuminate objects up to a distance of about 2 meters.

Note that when the night vision LEDs are turned on, the image on the parent unit will be displayed in

black /white.

Attention: infrared beams cannot be perceived by the human eye; it is not possible to detect that the

LEDs have been switched on with the naked eye. However, depending on the type infrared LED there

may be a red glow which is visible.

5 EXPANDING MULTIPLE CAMERAS

5.1 GENERAL:

The DVM-50 parent unit can register up to 4 cameras. The parent unit can select the desired camera

by scrolling through the menu. Using the menu on the DVM-50 parent unit you can select the desired

camera or you can rotate all the connected cameras using the (scan function).

Note: the receiver does NOT automatically switch to the camera where sound is detected.

Expansion Cameras (DVM-51) are available through the Alecto service desk either by phone: 073

6411 355 (NL), 03 238 5666 (B), 0180 503 0085 (D), or via the website at: www.alecto.info.

5.2 REGISTRATION OF EXTRA CAMERAS:

1. Connect the power adapter to the new baby unit, put the other end of the adapter into a 230V elec-

trical outlet and turn on the camera..

2. Press the button on the parent unit 4x.

3. Use the

and

buttons to select a free ‘camera connection’.

A ‘ ‘behindacameranumberwillindicatethatacameraisalreadyloggedontoaspecic

connection. If you connect a new camera to this number, the connection with the old camera

will be lost; preferably chose a camera number without a ‘ ‘ next to it.

4. Press the

button for 2 seconds button until the picture appears.

5. Press once on the button, the lightwillashquickly.

6. Within 10 seconds, press once on the PAIRING button located at the back of the new camera. The

lightindicatoronthefrontofthecamerawillashquickly.

7. After a few seconds, the parent unit will have found the new camera and the picture will be shown

on the display of the parent unit.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alecto DVM 50 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info