Bedienungsanleitung Alecto WS-3400 (Seite 48 von 58) (Deutsch, Englisch, Holländisch, Französisch)

707374

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

Indoor unit:

Slide the battery cover at the rear downwards, insert 2 AA 1.5V batteries as indicat-

ed inside the battery compartment and replace the battery cover on the indoor unit.

(Batteries are not included)

The indoor unit now starts searching for the outdoor unit for 1 minute. Insert the

batteries into the outdoor unit within this minute.

Outdoor unit:

Open the battery compartment by loosening the top of the outdoor unit. Open the battery compartment by

removing the cover. Insert 3 AA 1.5V batteries according to the image above. Pay attention to the polarity (+

and -) while doing so. Replace the cover and secure the top back onto the base (batteries are not included).

Mount the sensor onto a pole (28~40 mm) using the clips with the large screws and bolts.

Preferably, install the outdoor unit at least 1.5m above ground level in an open space within the transmitting

range of the outdoor unit to the indoor unit, making sure it can freely catch the wind.

Remarks:

• After replacing the batteries of the outdoor unit or after an interruption of the connection with the outdoor

unit, press the “SCAN” button on the indoor unit to reconnect the outdoor and indoor unit.

• Avoid placing the unit in direct sunlight, rain or snow.

• Try multiple locations to obtain the best possible reception between the outdoor unit (transmitter) and

indoor unit (receiver).

3.2 Paring the indoor unit / outdoor unit:

Automatically:

As soon as the batteries are inserted into the indoor unit, the indoor unit starts searching a signal from the

outdoor unit for 1 minute. So, when you insert batteries into the outdoor unit within this minute and the units

‘nd’ each other, these units will be paired automatically. The display of the indoor unit shows the tempera-

ture, humidity and wind speed as transmitted by the outdoor unit.

Manually:

If the units cannot automatically nd each other, or after replacing the batteries, you may pair the outdoor

unit with the indoor unit (again) as follows:

1. Press and hold the SCAN button for 2 seconds, the antenna symbol in the display starts ashing

2. Or alternatively briey press the RESET button at the bottom of the outdoor unit

3. After several seconds the units will nd each other (again)

3.3 Location:

Indoor unit:

You may choose to suspend the indoor unit from a wall with a simple screw or to use

it as a desk model with the supplied stand. In any case, never place the indoor unit in

direct sunlight or next to a heat generating light or stove.

Outdoor unit:

You may install the outdoor unit on a pole (excluded). In any case, make

sure to place the unit preferably 1.5 metres above ground level where it

can freely catch the wind.

AA 1,5V

reset

Not

included

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alecto WS-3400 Seite 48

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info