707374
50
Zoom out
Zoom in
Vorherige Seite
1/58
Nächste Seite
50
3.5 To reset measured data:
After completing the installation, press and hold the “HISTORY” button for 10 seconds to delete all data
measured up to that point. This avoids looking at measurements at a later time that were caused by
movements during installation.
4. USE
4.1 General functions:
The display shows the following basic functions / data:
DST
AM
PM
PST
MST
CST
EST
AST
NST
2 3
9
4 51
10
6 7
118 12
1. Appears when the battery of the indoor unit is nearly empty
2. Appears when pressing the MEM button to show the maximum or minimum value in the display (*1)
3. AM/PM (morning or afternoon) display in 12-hour format.
4. Display of the actual time
5. Display of the day of the week (*2)
6. Display of the month and date
7. Appears when the summertime is set (DST - Day Saving Time) (only when the DCF-77 is switched on
and being received correctly)
8. No operation
9. Appears with the display of the history
10. Appears when the alarm clock is set and activated
11. Appears in case of the frost alert (see chapter 5)
12. Appears when the DCF clock radio signal is being received
*1: By repeatedly pressing the “MEM” button, the following data are shown on the display in the order of:
1. Maximum indoor temperature
2. Minimum indoor temperature
3. Maximum humidity indoors
4. Minimum humidity indoors
5. Maximum outdoor temperature
6. Minimum outdoor temperature
7. Maximum humidity outdoors
8. Minimum humidity outdoors
9. Maximum physiological temperature
10. Minimum physiological temperature
11. Maximum heat index
12. Minimum heat index
13. Maximum dew point temperature
14. Minimum dew point temperature
15. Maximum wind chill
16. Minimum wind chill
17. Maximum average wind speed
18. Maximum speed wind gust
The upper part of the display shows on which day and at what time the concerned minimum of maximum
value was measured.
Press and hold the MEM button for 2 seconds to delete the displayed memory.
*2: By pressing the button you may switch the display of the clock between “seconds” display and “day”
display.
4.2 Contrast setup:
Repeatedly press the button to adjust the display contrast of the indoor unit. Each time you press the
button, the contrast is decreased in increments of 8. After the lowest setting the contrast is switched back to
the highest setting.
50

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Alecto WS-3400 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info