794955
41
Zoom out
Zoom in
Vorherige Seite
1/90
Nächste Seite
41
RAIN
To select the rainfall display mode
Press [ RAIN ] key to toggle between:
1. DAILY - the total rainfall from midnight (default)
2. WEEKLY - the total rainfall of the current week
3. MONTHLY- the total rainfall of the current calendar month
4. TOTAL - the total rainfall since the last reset
5. RATE - Current rainfall rate (base on 10 min rain data)
Period of rainfall and rain rate
In normal mode, press and hold [ Rain ] key for 6 seconds to reset all the rainfall records.
To ensure to have correct data, please reset all the rainfall record when you re-install your wireless 7-IN-1
sensor to other location.
LIGHT INTENSITY & UV INDEX
The UV index and light intensity reading show on the bottom right
side of the display.
The console can show the different reading’s daily MAX / MIN records in memory mode.
To view MAX / MIN records
In normal mode, press [ MEM ] key on the front side, to check records in below sequence:
Indoor or current CH MAX temperature Indoor or current CH MIN temperature Indoor or current CH MAX humidity
Indoor or current CH MIN humidity outdoor MAX temperature outdoor MIN temperature outdoor MAX
humidity outdoor MIN humidity MAX Feels like temperature MIN Feels like temperature MAX heat index
temperature MIN wind chill temperature MAX dew point temperature MIN dew point temperature MAX
average wind speed MAX gust wind MAX Beaufort MAX relative baro pressure MIN relative baro pressure
MAX absolute baro pressure MIN absolute baro pressure MAX rain rate MAX UV index, MAX light
intensity. Then press [ MEM ] key for back to normal mode.
You can also, press another key to exit memory mode.
Press and hold [ MEM ] key for 2 seconds to reset the current displayed record.
CALIBRATION
The console is able to calibrate the weather readings:
1. In normal mode, press and hold [ CAL ] key for 2 seconds to enter the
calibration mode as shown on the right.
2. Press [ CH / SET ] key to select different parameter as sequence: Indoor
temperature Indoor humidity CH temperature CH humidity
outdoor temperature outdoor humidity wind speed wind direction
absolute baro pressure rain gain UV gain light intensity gain.
3. While the reading is blinking, press [ WIND / + ] or [ - ] key to adjust the offset
value.
4. When finished, press [ CH / SET ] to proceed with next calibration by
repeating process 2 - 3 above.
5. To return normal mode, press [ CAL ] key once.
41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Alecto WS5400 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info