794955
42
Zoom out
Zoom in
Vorherige Seite
1/90
Nächste Seite
42
BACK LIGHT
The main unit back light can be adjusted, using the [ ON / AUTO ] sliding switch to select the Appropriate brightness:
Slide to the [ ON ] position to set the back light to normal brightness.
Slide to the [ AUTO ] position to set the back light brightness that according to ambient light level.
SET LCD DISPLAY CONTRAST
In normal mode, press [ SNOOZE / CONTRAST ] key to adjust LCD contrast for best viewing on table stand or wall
mounted.
7. MAINTENANCE
BATTERY REPLACEMENT
When low battery indicator “ ” is displayed in Out or CH section of the LCD display, it indicates that the wireless 7-in-1
or current channel sensor battery power give wireless sensor shown is low respectively. Please replace with new batteries.
WIRELESS 7-IN-1 SENSOR MAINTENANCE
REPLACE THE WIND VANE
Unscrew and remove the wind vane for
replacement
REPLACE THE WIND CUP
1. Remove rubber cap and Unscrew
2. Remove the wind cup for replacement CLEANING THE RAIN COLLECTOR
1. Rotate the rain collector by turning it
30°anti-clockwise.
2. Gently remove the rain collector.
3. Clean and remove any debris or insects.
4. Install the collector when it is clean and
fully dried.
CLEANING THE UV SENSOR AND
CALIBRATION
For precision UV measurement, gentle
clean the UV sensor cover lens with damp
micro-ber cloth.
Over time, the UV sensor will naturally
degrade. The UV sensor can be calibrated
with a utility grade UV meter, please refer
to Calibration section in previous page for
about the UV sensor calibration.
CLEANING HYGRO-THERMO SENSOR
1. Remove the 2 screws at the bottom of the
radiation shield.
2. Gently pull out the bottom 4 shields.
3. Carefully remove any dirt or insects on the
sensor and ventilation fan (do not let the
sensors inside get wet).
4. Clean the shield with water to remove any
dirt or insects.
5. Install all the parts back when they are clean
and fully dried.
42

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Alecto WS5400 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info