Bedienungsanleitung Alpina ATR 26 J (Seite 17 von 27) (Alle Sprachen)

731964

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

risk of hazards and improve the quality of your

work.

21) Check that when the machine is running

idle, there is no movement of the cutting means

and, after pressing the throttle trigger, the engine

quickly returns to minimum speed.

22) Always keep the machine connected to the

harness when working.

23) Stop the engine:

– Whenever you leave the machine unattended;

– Before refuelling;

– When moving between work areas.

24) Stop the engine and disconnect the spark

plug cable:

– Before checking, cleaning or working on the

machine;

– After the intake of a foreign body. Inspect the

machine for damage and make repairs before

restarting and operating the machine;

– If the machine begins to vibrate abnormally

(Immediately look for the causes of the vibra-

tions and take it to a Specialised Centre for

necessary inspections);

– When the machine is not in use.

25) Avoid using the machine in environments or

at times of the day when it may disturb others.

26) To avoid the risk of re, do not leave the ma-

chine with the engine hot on leaves, dry grass or

other inammable material.

27) Never assemble metal cutting means. The

use of metal or rigid cutting means of any type

with this machine is prohibited.

28) WARNING – If something breaks or an ac-

cident occurs while working, turn o the engine

immediately and move the machine away to pre-

vent further damage; if an accident occurs with

injuries or third parties are injured, carry out the

rst aid measures most suitable for the situation

immediately and contact the medical authorities

for any necessary health care. Carefully remove

any debris that might cause damage or harm

persons or animals should it not be seen.

29) WARNING – The noise and vibration lev-

els shown in these instructions are the maxi-

mum levels for use of the machine. The use of

an unbalanced cutting means and the absence

of maintenance have a signicant inuence on

noise emissions and vibrations. Consequently,

it is necessary to take preventive steps to elimi-

nate possible damage due to high levels of noise

and stress from vibration. Maintain the machine

well, wear ear protection devices, and take

breaks while working.

30) Prolonged exposure to vibrations can cause

injuries and neurovascular disorders (also called

“Raynaud’s syndrome” or “white hand”), espe-

cially to people suering from circulation dis-

orders. The symptoms can regard the hands,

wrists and ngers and are shown through loss of

sensitivity, torpor, itching, pain and discolouring

of or structural changes to the skin. These ef-

fects can be worsened by low ambient temper-

atures and/or by gripping the handgrips exces-

sively tightly. If the symptoms occur, the length of

time the machine is used must be reduced and a

doctor consulted.

D) MAINTENANCE AND STORAGE

1) WARNING! – Before cleaning or doing main-

tenance work, disconnect the spark plug cap

and read the relevant instructions. Wear proper

clothing and protective gloves whenever your

hands are at risk.

2) WARNING! – Never use the machine with

worn or damaged parts. Faulty or worn-out parts

must always be replaced and not repaired. Use

original spare parts only: the use of non-original

and/or incorrectly tted parts will jeopardize the

safety of the machine, may cause accidents or

personal injuries for which the Manufacturer is

under no circumstance liable or responsible.

3) Any adjustments or maintenance operations

not described in this manual must be carried out

by your Dealer or a specialized Service Centre

with the necessary knowledge and equipment

to ensure that the work is done correctly main-

taining the machine’s original safety level. Any

operations performed in unauthorized centres or

by unqualied persons will totally invalidate the

Warranty and all obligations and responsibilities

of the Manufacturer.

4) After each use, disconnect the spark plug ca-

ble and check for damage.

5 Keep all nuts, bolts and screws tight to be sure

the machine is in safe working condition. Routine

maintenance is essential for safety and for main-

taining a high performance level.

6) Check that the cutting means screws are

properly tightened on a regular basis.

7) Wear work gloves and apply the cutting

means guard to handle, remove or remount the

same.

8) Be careful during adjustment of the machine

to prevent entrapment of the ngers between the

cutting means and xed parts of the machine.

9) Do not touch the cutting means until the spark

plug cable has been disconnected and the cut-

ting means is completely stationary. When serv-

icing the cutting means, bear in mind that, even

though the spark plug cable is disconnected, the

cutting means can still move.

10) Check the guard frequently for wear or dete-

rioration. Replace it if it is damaged.

11) Replace any instruction or warning message

stickers, if damaged.

12) Store the machine out of the reach of chil-

dren.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alpina ATR 26 J Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info