Bedienungsanleitung Alpina C 1.8 (Seite 11 von 23) (Alle Sprachen)

732004

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

PACKAGING CONTENTS

The packaging contains:

– power unit,

– bar,

– chain,

– bar cover,

– bag containing equipment and documents.

IMPORTANT

The machine is supplied with

the bar and chain dismantled and the oil tank

empty.

WARNING! Unpacking and complet-

ing the assembly should be done on a at and

sta ble surface, with enough space for ma

chi ne handling and its packaging, always

making use of suitable equipment.

Disposal of the packaging should be done in

ac cordance with the local regulations in for ce.

BAR AND CHAIN MOUNTING

WARNING! Always wear heavy-duty

gloves when handling the bar and chain.

Mount the bar and chain very carefully so as

not to impair the safety and eciency of the

m achine. If in doubt, contact your dealer.

Before tting the bar, make sure the chain brake is

not engaged; this is done by pulling the front hand

guard right back towards the body of the machine.

WARNING! Make sure the machine is

not plugged into the mains socket.

• MACHINES WITH STANDARD

CHAIN TENSION ADJUSTER

– Remove the rubber protection (1a), unscrew the

nut (1) and remove the guard to get to the drive

sprocket and the point where the bar is tted

(Fig. 1).

– Mount the chain in the right direction on the bar.

If the tip of the bar has a nose sprocket, make

sure the drive links are correctly inserted in the

sprocket rims (Fig. 2).

– Mount the bar (2) by inserting the stud bolt in

the groove and push it towards the back of the

machine body and wind the chain around the

drive sprocket (Fig. 3).

– Check that the chain tension adjuster pin (3) is

tted properly in the hole on the bar (Fig. 4); if

it isn’t, turn the chain tension adjuster screw (4)

using a screwdriver until the pin is comple tely

inserted (Fig. 5).

– Fit the guard back on without tightening the nut

(1).

– Turn the chain tension adjuster screw (4) to ad-

just the chain tension (Fig. 5).

– Raise the bar and tighten the guard nut (1)

securely using the supplied wrench, then re-

place the rubber protection (1a) (Fig. 6).

• MACHINES WITH QUICK CHAIN TENSION

ADJUSTER

– Unscrew the handle (11) and remove the

guard to get to the drive sprocket and the point

where the bar is tted (Fig. 1a).

– Mount the chain in the right direction on the bar.

If the tip of the bar has a nose sprocket, make

sure the drive links are correctly inserted in the

sprocket rims (Fig. 2).

– Mount the bar (2) by inserting the stud bolt in

the groove and push it towards the back of the

machine body and wind the chain around the

drive sprocket (Fig. 3).

– Fit the guard back on without tightening the han-

dle (11). Check that the chain tension adjuster

pin (3) is tted properly in the hole on the bar

(Fig. 4); if it isn’t, turn the chain tension adjuster

ring-nut (12) until the pin is completely inserted

(Fig. 5a).

– Turn the ring-nut (12) to obtain the desired chain

tension level (Fig. 5a).

– Raise the bar and tighten the handle (11)

securely (Fig. 6a).

6 MACHINE ASSEMBLY

4. MACHINE ASSEMBLY

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alpina C 1.8 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info