Bedienungsanleitung Alpine iDE178BT (Seite 20 von 53) (Englisch)

536907

Zoom out

Zoom in

Vorherige Seite

1/53

Nächste Seite

20-EN

Turn the Rotary encoder to adjust the level, and then

press ENTER.

LEVEL: 0 ~ 8

Repeat steps 3 to 4 to complete the setting of other bands.

Note

• There is no MX mode for FM, MW and LW radio.

You can change the unit, (cm or inch) of time correction.

 Setting item: TCR Parameter

Setting contents:

cm (Initial setting) / inch

cm:

Time correction value is in centimetres.

inch:

Time correction value is in inches.

Before performing the following procedures, refer to “About Time

Correction” on page 21.

After selecting T.Correction from the Audio Setup mode,

turn the Rotary encoder to select a speaker to be

adjusted, and then press ENTER.

F-L

 F-R

 R-L

 R-R

 SW-L  SW-R

*1 Front-L

*2 Front -R

*3 Rear-L

*4 Rear-R

Turn the Rotary encoder to adjust the distance of the

selected speaker, and then press ENTER.

0.0 cm to 336.6 cm (3.4 cm/step)

0.0 inch to 132.7 inch (1.3 inch/step)

Note

• The total adjustment distance for all speakers should be less than 510

centimetres (201 inches).

Repeat steps 1 and 2 to set another speaker.

By setting these values to make its sound reach the listening

position at the same time as the sound of other speakers.

This function allows you to change the sound field easily.

There are three modes to choose from. For details, refer to the table

below.

Before performing the following procedures, refer to “About the

Crossover” on page 22.

After selecting X-Over from the Audio Setup mode, turn

the Rotary encoder to select the desired channel, and

then press ENTER.

Turn the Rotary encoder to select the desired frequency

within the selected channel, and then press ENTER.

Repeat step 2 to adjust the slope and Level within the

selected channel.

Adjusting the Channel (Ch.)

Setting contents:

Front (HPF) / Rear (HPF) / SUBW (LPF)

Selecting the Cut-Off Frequency (Freq.)

Setting contents:

20 / 25 / 31.5 / 40 / 50 / 63 / 80 (Initial setting) / 100 / 125 /

160 / 200 (Hz)

Adjusting the Slope

Setting contents:

Flat (Initial setting) / 6 / 12 / 18 / 24 dB/oct.

Adjusting the Level (Lev.)

Setting contents:

−12 to 0 (dB) (Initial setting: 0)

The Parametric EQ/T.Correction and X-Over settings can be stored in

the preset memory.

The Parametric EQ/T.Correction/X-OVER settings can be

stored in any one of the preset buttons(1 through 6).

After completing any adjustment for Parametric EQ/

T.Correction/X-OVER (e.g. Band), press and hold the

desired preset button for at least 2 seconds.

Turn the Rotary encoder to select Protect YES/NO, and

then press ENTER to store the adjusted contents.

Protect NO  Protect YES (Initial setting)

Notes

• If Protect YES is selected, the adjusted contents are protected and stored

into the preset buttons. When you want to store the parameter into a

protected preset button, “Replace NO/YES” can be selected.

If Protect NO is selected, the preset is stored.

• While perform this operation, all adjusted contents of Parametric EQ/

T.Correction and X-Over will be stored in the preset buttons.

• The stored contents are not deleted even when resetting the unit or

disconnecting the battery.

• The stored contents can be recalled by performing operation (refer to

“Recalling the Stored Parametric EQ/T.Correction/X-Over Settings” on

page 21).

Setting the Time Correction Unit

(TCR Parameter)

Adjusting the Time Correction

(T.Correction)

Adjusting the SPATIAL

Mode Effect

OFF

(Initial setting)

No effect is applied.

OFF status

Front Wide

Creates the effect of widening the front sound

field by delaying the sound of the front

speakers.

Rear Wide

Creates the effect of making the front sound

image clear and far by delaying the sound of

the rear speakers.

Adjusting the Crossover Settings (X-Over)

Storing the Parametric EQ/T.Correction/

X-Over Settings

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alpine iDE178BT Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Alpine iDE178BT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info