Bedienungsanleitung Alpine PXA-H701 (Seite 24 von 52) (Englisch)

66420

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

22-EN

Using Dolby Surround

OFF:

When no speaker is connected

SMALL:

When a speaker that cannot play low

frequencies (80 Hz or less) is connected

LARGE:

When a speaker that can play low frequencies

(80 Hz or less) is connected

*1: It is not possible to set the front speakers to

“OFF”.

*2: If the front speakers are set to “SMALL”, the

rear and centre speakers cannot be set to

“LARGE”.

6 Press the SETUP button repeatedly to quit the

setup mode.

NOTES

• If the centre speaker is turned “OFF”, the centre

channel's audio signals are added to the audio

signals output from the front speakers.

• If you set the speaker response to “OFF”, also set

the speaker setting to “OFF”. (See page 4.)

• Perform the setup for all the speakers (“Front”,

“Center”,“Rear” and “Sub. W”). If not, the sound

may not be balanced.

• When centre is set to subwoofer, the setting is

ineffective even if centre is set with this function.

• Once the settings are made, we recommend storing

them in the memory. See page 28 for instructions.

• Through changing the settings on each speaker, a

change in the output of the other speakers may occur

due to the setting requirements.

• When using the PRO LOGIC II, if the rear speaker is

set to “LARGE”, then there will be no output from

the sub-woofer.

Adjusting the speaker levels

Use the PXA-H701’s test tones to make the

volume adjustments of the different speakers.

When levels are equal, a strong sense of

presence can be heard from the different

speakers at the listening position.

NOTE

Avoid stopping, pausing, switching the disc, cueing,

fast-forwarding or switching the audio channel of the

player while making this adjustment. The setting is

cancelled if the decode mode is switched.

1 Press the SETUP button.

The setup mode is set.

2 Turn the Rotary encoder to select the “5.1CH

SETUP” mode, then press the ENTER button.

3 Turn the Rotary encoder to select “OUTPUT

LEVEL”, then press the ENTER button.

CHANNEL

ENTER

SETUP

Rotary encoder

Speaker setup

The PXA-H701 can be set according to the

playable frequency range of your speakers.

Check the playable frequency range of the

speakers (not including the subwoofer) before

performing this operation to verify whether the

speakers can play low frequencies (of about 80

Hz or less).

NOTE

Avoid stopping, pausing, switching the disc, cueing,

fast-forwarding or switching the audio channel of the

player while making this adjustment. The setting is

cancelled if the decode mode is switched.

1 Press the SETUP button.

The setup mode is set.

2 Turn the Rotary encoder to select the “5.1CH

SETUP” mode, then press the ENTER button.

3 Turn the Rotary encoder to select the

“SPEAKER SETUP”, then press the ENTER

button.

4 Press the CHANNEL button to select the

speaker, then press the ENTER button.

5 Turn the Rotary encoder to select the speaker

property, then press the ENTER button.

Repeat steps 4 and 5 to set the various items.

(Subwoofer is only ON/OFF.)

OFF SMALL LARGE

Front Center Rear Sub. W

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alpine PXA-H701 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info