Bedienungsanleitung Alpine PXA-H701 (Seite 25 von 52) (Englisch)

66420

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

23-EN

4 Turn the Rotary encoder to select “Auto”, then

press the ENTER button. Test tone output is

repeated for each of the different speaker

channels. They will be repeated in the order

shown below.

If no operation is performed for 2 seconds, the

channel switches to the next channel.

5 While the test tones are being produced from the

speakers, turn the Rotary encoder to adjust so

that the volume of the different speakers is

equal.

• The adjustment range for the different

speakers is ± 10 dB.

• Adjust based on the front speakers.

6 Press the SETUP button repeatedly to quit the

setup mode.

Adjusting the level for individual speakers

(manual)

1) At step 4 above, select “Manual”, then press the

ENTER button.

2) Press the CHANNEL button or ENTER button to

select the speaker you wish to adjust.

3) Turn the Rotary encoder to adjust the output

level.

4) Repeat steps 2) and 3) above to adjust the levels

of the different speakers.

5) Press the SETUP button again to quit the setup

mode.

NOTES

• If a speaker is set to the off mode, that speaker’s level

adjustment cannot be made.

Refer to “Speaker setup” (page 22).

• Once the settings are made, we recommend storing

them in the memory. See page 28 for instructions.

RS (Right surround)

LS (Left surround)

L (Left front) C (Center)

R (Right front)

1 Press the SETUP button.

The setup mode is set.

2 Turn the Rotary encoder to select the “5.1CH

SETUP” mode, then press the ENTER button.

3 Turn the Rotary encoder to select “REAR MIX”,

then press the ENTER button.

4 Turn the Rotary encoder to select “REAR MIX

ON” or “REAR MIX OFF”, then press the ENTER

button.

When set to “ON”, the front audio signals are

mixed into the audio signals output from the rear

speakers.

5 Turn the Rotary encoder to adjust the level,

then press the ENTER button.

The level can adjusted in five steps: –6, –3, 0, +3

and +6. The higher the level, the more bass is

output from the rear speakers. (The effect differs

according to the software (DVD, etc.).)

6 Once the settings are completed, press the

SETUP button repeatedly to quit the setup

mode.

NOTES

• This adjustment is ineffective when the rear speaker

setup setting is set to “OFF”.

• For linear PCM signals, the voice is output from the

rear speaker regardless of the REAR FILL and REAR

MIX setting.

• Once the settings are made, we recommend storing

them in the memory. See page 28 for instructions.

Mixing bass sound to the rear channel

This function mixes the front channel audio

signals to the audio signals output from the rear

speakers, improving the sound in the vehicle’s

rear seat.

NOTE

Avoid stopping, pausing, switching the disc, cueing,

fast-forwarding or switching the audio channel of the

player while making this adjustment. The setting is

cancelled if the decode mode is switched.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alpine PXA-H701 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info