Bedienungsanleitung Alpine RUX-C800 (Seite 29 von 67) (Englisch)

471407

Zoom out

Zoom in

Vorherige Seite

1/67

Nächste Seite

27-EN

01GB06PXAH800.fm

ALPINE PXA-H800_EN 68-13530Z65-A (B5)

From a PC

: Both R and L channels are set at the same value (The

initial setting).

: Channels R and L can be set independently.

• When you select “ ,” a message to confirm which of the R or L

channel set up values is to be applied will be displayed. Click either

[LEFT] or [RIGHT].

Click the channel you want to adjust.

• Channels to be set vary depending on the system set in “Setting the

Speaker System (Output System Select)” (page 13).

Drag the setup point up or down or to the right or left

to make adjustments.

The arrow indicating the dragging direction appears.

The cutoff frequency band varies depending on the channel

(speaker) (see “About the Crossover (X-Over)” page 26).

Slope: 0 (OFF)/-6/-12/-18/-24/-30/-36 dB/oct*

Level: -24 to 0dB (in 0.5 dB steps)

* Neither LPF of Subwoofer nor HPF of Front High can be set at 0

(OFF).

• Show All Curves:

When you click the [Show All Curves], the curves for all the channels

will be displayed.

• Hide Other Curves:

When you click the [Hide Other Curves], only the curve of the

channel for which you are making adjustments is displayed.

• You can also make adjustments by operating the settings indication

area.

The current setup value will be displayed at the bottom of the Screen.

Click [ ] and select and click a setup value. You can also use the

[Tab], [ ], [ ], [ ], and [ ] keys on your PC to select the

setup value.

• The unadjusted curve display can be turned off in the following steps.

1 Click the indicator of “Show.”

The indicator will be turned off and the curve display of

the selected channel is hidden.

2 To turn on the display, click the indicator of “Show” again.

Click [0°] or [180°] to switch the phase.

To adjust another channel, repeat Steps 3 through 5.

• By clicking either [ ] or [ ] of “Mute” while in the adjustment

mode, you can mute the selected channel.

When setting is complete, click [Close Window].

• To restore the channel which is currently being adjusted to the

default, click [Ch. Flat]. To restore all the channels to the initial

settings, click [All Reset]. Click [OK] when each confirmation

message appears.

• When Tweeter is selected for “Front 1” to protect the speaker, there

is no filter off (Slope OFF) setting for HPF. There is no filter off

(Slope OFF) setting for Subwoofer LPF, either.

• When the speaker is set to the “OFF” mode, the X-Over for that

speaker cannot be set. Refer to “Setting the Speaker System (Output

System Select)” (page 13)/ “Setting the Speakers (Speaker Setup)/

Setting the Subwoofers” (page 14).

• Check the playback frequencies of the connected speakers before

adjusting.

• After the setting, it is recommended to store the setting contents on

the unit. For details, refer to “Storing the Preset Values (Preset

Store)” (page 12).

Setup point

Frequency Level

Slope

Indicator

01GB00PXAH800.book Page 27 Tuesday, February 8, 2011 9:04 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alpine RUX-C800 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info