Bedienungsanleitung Alpine X800D-ML (Seite 55 von 116) (Englisch)

572063

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

55-EN

Adjusting the Time Correction

(Time Correction)

[Time Correction] is selected on the Sound setup menu in step 3. Refer

to “Sound Setup Operation” (page 52).

Before performing the following procedures, refer to “About Time

Correction” (page 56).

Setting item: Time Correction

Touch [cm], [inch] or [ms] to select mode for

making adjustments.

Each time you touch, the onscreen button and correction

mode changes.

cm/inch: Adjust listening position and distance from each

speaker.

ms: Adjust time.

Touch [] or [] for each speaker to adjust the

time or distance.

0.0 msec to 9.9 msec (0.1 msec/step)

0.0 cm (0.0 inch) to 336.6 cm (132.7 inch) (3.4 cm/step)

All speaker setting values are adjustable in the range of 15 ms

or 510 cm.

To store the adjusted setting value, touch and hold

[Preset1], [Preset2], or [Preset3] for at least 2

seconds.

• Touch [Flat] to set all values to 0.0.

• If the Rear Speaker setting is “Off”, the Rear Speaker setting cannot

be edited (refer to page 52).

• If the Subwoofer setting is “Off”, the Subwoofer setting cannot be

edited (refer to page 52).

Calling the Time Correction Value

Calling the pre-set time correction value.

Touch [Preset1], [Preset2], or [Preset3] on the time

correction screen.

The setting stored in the Preset will be recalled.

Adjusting the Crossover Settings

(X-OVER)

[X-OVER] is selected on the Sound setup menu in step 3. Refer to

“Sound Setup Operation” (page 52).

Before performing the following procedures, refer to “About the

Crossover” (page 57).

Setting item: X-OVER

Touch [Channel] to select the channel.

Each time you touch, the channel switches.

• The channel being adjusted is displayed in red.

Adjust the crossover to your preference.

Selecting the Cut-Off Frequency

Touch [] or [] of “Freq.”, and then select the cut-off

frequency.

Setting contents: 20 / 25 / 31.5 / 40 / 50 / 63 / 80 (Initial setting) /

100 / 125 / 160 / 200 Hz

Adjusting the Slope

Touch [] or [] of “Slope”, and then adjust the HPF or LPF

slope.

Setting contents: 0 (Initial setting) / 6 / 12 / 18 / 24 dB/oct.

Adjusting the Level

Touch [] or [] of “Level”, and then adjust the HPF or LPF

level.

Setting contents: -12 to 0 dB (Initial setting: 0)

Repeat steps 1 to 2 to make adjustment to the other

channels.

To store the adjusted setting value, touch and hold

[Preset1], [Preset2], or [Preset3] for at least 2

seconds.

• Touch [Flat] to initialise all values.

• If the Rear Speaker setting is “Off”, the Rear Speaker setting cannot

be edited (refer to page 52).

• If the Subwoofer setting is “Off”, the Subwoofer setting cannot be

edited (refer to page 52).

• While adjusting the X-OVER you should consider the frequency

response of the connected speakers.

Correction mode

Front HPF Rear HPF Subw. LPF

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alpine X800D-ML Seite 55

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Alpine X800D-ML

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info