Bedienungsanleitung Alpine X800D-ML (Seite 58 von 116) (Englisch)

572063

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

58-EN

• HPF (high pass filter): Cuts the lower frequencies and allows the

higher frequencies to pass.

• LPF (low pass filter): Cuts the higher frequencies and allows the

lower frequencies to pass.

• Slope: The level change (in dB) for a frequency change of one octave.

• The higher the slope value, the steeper the slope becomes.

• Adjust the slope to FLAT to bypass the HP or LP filters.

• Do not use a tweeter without the HPF on or set to a low frequency, as

it may cause damage to the speaker due to the low frequency content.

• You cannot adjust the crossover frequency higher than the HPF or

lower than the LPF.

• Adjustment should be made according to the recommended crossover

frequency of the connected speakers. Determine the recommended

crossover frequency of the speakers. Adjusting to a frequency range

outside that recommended may cause damage to the speakers.

For the recommended crossover frequencies of Alpine speakers, refer

to the respective Owner’s Manual.

We are not responsible for damage or malfunction of speakers caused

by using the crossover outside the recommended value.

Source Setup Operation

Touch [Setup] icon of Top banner.

The Setup main screen is displayed.

Touch [ (Source)].

The Source Setup screen appears.

Select the desired item.

Setting items: Source Layout / Disc / Radio / DAB / AUX / RSE /

TuneIt

Touch [] or [] etc., to change its setting.

• When the pop-up window for setup is displayed, touch [] to

close the window after setting.

Touch [] to return to the previous screen.

• Immediately after changing the Source Setup (while the system is

writing data automatically) do not turn the ignition key to OFF.

Otherwise, the settings may not be changed.

Source Layout Setting

[Source Layout] is selected on the Source setup menu in step 3.

Refer to “Source Setup Operation” (page 58).

You can set whether to switch sources by swiping from the designated

area of the Audio/Visual Playback screen from right to left or from left

to right. Refer to “Switching Sources” (page 27).

Setting item: Slide Source Change

Setting contents: On (Initial setting) / Off

You can select this menu displayed on left or right of screen.

Setting item: Sound Setup Position

Setting contents: Left (Initial setting) / Right

You can customize the Source Banner order as you prefer. The source

switching order is displayed according to your changes.

Setting item: Source Banner Customize

Take adjusting the order of Disc and AUX-1 as an

example:

Touch the desired source icon ([Disc] etc.).

The [Disc] source icon is displayed highlighted.

Touch this icon again to cancel.

Touch another source icon ([AUX-1] etc.).

The Source Banner positions for [Disc] and [AUX-1] are

swapped.

Source Setup

The following steps 1 to 5 are common operations to each

“Setting item” of Source Setup. Refer to each section for details.

Setting the Slide Source Change

On: Source is changed by a swipe gesture.

Off: Source is not changed by a swipe gesture.

Setting the Easy Sound Setup Position

Customizing the Source Banner

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alpine X800D-ML Seite 58

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Alpine X800D-ML

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info