Bedienungsanleitung Angelcare AC300 (Seite 4 von 48) (Alle Sprachen)

537059

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Warnings

• This product is NOT a medical device nor a device to prevent cases of

Sudden Infant Death Syndrome (SIDS).

• This product is NOT a substitute for direct supervision of your baby.

Check your baby’s activities at regular intervals. Monitoring of

premature babies, or those considered to be at risk, should be carried

out only under the supervision of a doctor or health professional.

• The Sensor Pad may detect movement from many sources from

BOTH inside and outside your baby’s room, for example: fans,

washing machines, loud music, etc. Ensure that all vibration

sources are eliminated before using the Angelcare

Monitor.

Avoid contact with crib when monitor is in use. Refer to the

Movement Sensitivity Adjustment and Troubleshooting sections.

• ALWAYS place Monitor on flat surface in an upright position, away

from baby’s reach.

• DO NOT touch the end of the adapter cord when plugged into an

electrical outlet.

• This product should be serviced by qualified personnel. There are no

user serviceable parts inside monitor. Refer all service questions to

your distributor (see page 47).

Instructions

RETAIN INSTRUCTIONS: Keep user’s manual for future reference.

WATER, MOISTURE AND HEAT DAMAGE: Keep all components away

from water (sink, bath tub, swimming pool) and places that emit heat

(stove, radiator).

VENTILATION: ALWAYS place Monitor on flat surface in an upright

position so that air can flow freely around it.

CORD PROTECTION: Avoid damage to the Sensor Pad cord. The cord is

long enough to route so that it is not likely to be walked on or pinched

by items placed upon or a

gainst it.

CLEANING: Disconnect Monitor before cleaning. DO NOT immerse in

water. Use a dry cloth to keep Monitor free from dust.DO NOT spray with

cleaning products or solvents. Wipe Sensor Pad with a very slightly

damp cloth with an antiseptic or mild detergent.

OBJECT AND LIQUID ENTRY: Care should be taken so that objects do

not fall onto Monitor and that liquids are not spilled into either Monitor

or Sensor Pad through its openings.

NON-USE PERIODS: When not using monitor for long periods, remove

the batteries from Monitor.

4 EASY STEPS TO OPERATE YOUR ANGELCARE

MONITOR

STEP 1. SENSOR PAD

Position Sensor Pad as illustrated (Figures 1 and 2). The printed side of Sensor Pad MUST face up. DO NOT tuck thick bedding under the edges of the

mattress.

Sensor Pad must rest on a completely flat and rigid surface. If your crib has a flexible or uneven base (metal spring base, etc.), place a piece of

6 mm (1/4”) plywood to cover the full size of the crib base.

STEP 2 MONITOR

•

Insert 2 AA batteries into Monitor.

•

Connect the Sensor Pad cord to the monitor (Figure 3).

• On the side of the Monitor, select 1 of the 2 functions of how you want to monitor your baby:

“Ti

c” On:

see green movement indicator light flash

AND hear a “

Tic” sound with every movement baby makes.

“Tic” Off: Same as above BUT without the “Tic” sound.

NOTE: The sensitivity adjustment has been preset. DO NOT ADJUST UNLESS NECESSARY. If poor capture of movement (red flashing

light) or false alarm occurs, consult the Movement Sensitivity Adjustment section.

STEP 3 TO USE MONITOR

Place baby in crib and switch Monitor to the ON position. When removing baby from crib, switch Monitor to the OFF position. If you forget to switch

OFF, a “pre-alarm Tic” will sound after 15 seconds as a reminder.

STEP 4 BATTERY MODE

The Angelcare

Movement Monitor is battery operated. Batteries will last approximately 3 to 4 months. When monitor produces a rapid clicking

sound, change batteries promptly.

NOTE:

•

Test your Angelcare

Monitor BEFORE first-time use and then on a periodic basis.

• When monitor is in use, DO NOT use crib mobile or other crib accessories that produce vibrations. Alarm will not sound as monitor is

still detecting movement.

• The Angelcare

Monitor is perfectly safe. The Sensor Pad and the cord are entirely passive. They carry no electrical current and do

not radiate any form of energy.

• Your monitor can be used in any crib or sleeping area (that has NO motion or vibration) designed to safely hold a baby.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Angelcare AC300 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Angelcare AC300

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info