Bedienungsanleitung Angelcare AC300 (Seite 5 von 48) (Alle Sprachen)

537059

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Problem Possible Cause Solution

False alarms

Alarm will not sound

Alarm indicator light is flashing red

(monitor is barely detecting

movement)

Power ON indicator does not light up

TROUBLESHOOTING

• Baby was removed from crib and Monitor was not

switched OFF .

• Sensor Pad cord not connected properly to Monitor.

•

Sensor Pad is not in full contact with crib mattress, or crib

mattress is not resting on a completely flat or rigid surface.

• Baby has moved away from Sensor Pad, to the edge of the crib.

• Monitor is detecting movement when crib is being touched.

• Monitor is detecting movement from outside the crib such as

motorized devices, strong drafts, etc.

• Sensitivity is set too high.

• Sensor Pad is not in full contact with crib mattress, or crib

mattress is not resting on a completely flat or rigid surface.

• Baby is in a very deep sleep or has moved away from Sensor

Pad, to the edge of the crib.

• Batteries are low or improperly installed.

• The Monitor is not ON.

• Turn Monitor to the OFF position.

• Verify the connection between the Sensor Pad and Monitor.

Unplug and reconnect the cord.

• Make sure there is no bedding between mattress and Sensor

Pad. Sensor Pad must rest on a completely flat and rigid surface.

If your crib has a flexible or uneven base (metal spring base,

etc.), place a piece of 6 mm (1/4") plywood to cover the full size

of the crib base.

• Make sure Sensor Pad is positioned as described in the 4

Easy Steps section. Sensitivity may need to be adjusted,

consult the Movement Sensitivity Adjustment section.

• Avoid contact with the crib when monitor is ON.

• Place crib near a solid supporting wall to avoid Sensor Pad

from detecting movement from outside crib.

• You may need to decrease the sensitivity, consult the

Movement Sensitivity Adjustment section.

• Make sure there is no bedding between mattress and Sensor

Pad.Sensor Pad must rest on a completely flat and rigid surface:

place a piece of 6 mm (1/4”) plywood to cover the full size of the

crib base.

• Make sure Sensor Pad is positioned as described in the 4

Easy Steps section. Sensitivity may need to be adjusted,

consult the Movement Sensitivity

Adjustment section.

•

Check / replace ba

tteries.

• Check connections or change to another electrical outlet.

• Make sure Monitor is ON.

Testing Your Angelcare

Monitor

NOTE: Test your Angelcare

Monitor BEFORE first-time use and

then on a periodic basis.

The Angelcare

Monitor can be used outside of the crib, in a different

sleeping area. Test monitor when moving Sensor Pad to a new location

to ensure sensitivity is adjusted correctly to the new padding or

mattress. Consult the Movement Sensitivity Adjustment section.

Step 1 Switch the power and “Tic” function to the ON positions. Gently

place your hand on the mattress. The green light will continue to flash

with your every movement. Remove hand from mattress. Due to no

movement, a “pre-alarm Tic” sound will emit after 15 seconds. 5

seconds later, the alarm will sound and the red light will flash

continuously.

NOTE: If alarm does not sound, the Sensor Pad may be detecting a

continuous vibration from the floor, a strong draft or the crib is being

touched. Avoid contact with crib when monitor is in use. Place crib near

a solid supporting wall and away from strong air currents. The

sensitivity of the Sensor Pad may need to be reduced, consult the

Movement Sensitivity Adjustment section.

Step 2 To stop alarm, place your hand lightly on mattress for Sensor

Pad to redetect movement.The red Alarm indicator light on the Monitor

will continue to flash 1 minute (Figure 3).

Step 3 When Monitor produces a rapid “clicking” sound, replace

batteries promptly.

Movement Sensitivity Adjustment

The Sensitivity Adjustment Dial has been preset

to suit most situations. However in certain

circumstances, the sensitivity may not be ideal. DO

NOT increase sensitivity unless false alarms occurs

and you have followed the advice in the

Troubleshooting section for false alarms. Make a note

of the pre-set position of the dial should you wish to

return to it.

The Alarm Indicator Light on the Monitor will flash red when Monitor

barely detects movement. This could be a result of: baby being in a very

deep sleep or baby having moved away from Sensor Pad to edge of crib.

If alarm does NOT sound, no adjustment of sensitivity is required. If the

Alarm Indicator Light flashes red most of the time with baby directly over

the location of either Sensor Pad, a false alarm may occur. If this

happens, adjust the sensitivity.

To adjust sensitivity, increase dial to the next setting. Retest monitor.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Angelcare AC300 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Angelcare AC300

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info