Bedienungsanleitung Arcam AV888 (Seite 13 von 74) (Englisch)

482343

Zoom out

Zoom in

Vorherige Seite

1/74

Nächste Seite

E-11

English

Trigger connectors

e trigger connectors (TRIG Z1, TRIG Z2 and TRIG Z3)

provide an electrical signal whenever the amplier is

switched on and the relevant zone enabled.

e trigger signal can be used

to switch on and o compatible

pieces of home entertainment

equipment, for example, you

could set up a trigger to turn on

your television and DVD player

whenever the unit was switched

on.

ere are three trigger output

sockets on the unit, each capable

of outputting a 12V, 70mA

switching signal. e socket

is designed for mono 3.5mm jacks: tip is the trigger

output, sleeve is ground.

tip: Trigger output

sleeve: Ground

TRIG Z1

Use for remotely turning on and o power amps or

source equipment for Zone1. On = 12V, O = 0V.

TRIG Z2

Use for remotely turning on and o power amps or

source equipment for Zone2. On = 12V, O = 0V.

Infra-red (IR) connectors

e infra-red inputs (Z1 IR, Z2 IR

and Z3 IR) allow the connection of

external IR receivers, either when

the unit’s front panel IR receiver is

fully or partially obstructed or to

allow the use of a remote control

in Zone2 or Zone3.

ere are three IR inputs on the

unit, each designed for stereo or

mono 3.5mm jacks. Tip is the

modulated signal, sleeve is ground.

tip: Modulated signal

sleeve: Ground

Z1 IR

is input is intended for use with a local IR receiver

when the front panel of the unit is blocked.

Connecting an IR receiver to

Z1 IR will disable to front

panel IR receiver to prevent problems with multiple

commands if the front panel IR receiver is only partially

obstructed.

Z2 IR

is input is intended for use with an IR receiver in

Zone2 to allow remote control of the unit from a second

room.

SIRIUS

DAB

ETHERNET

Z2 IR

IR OUT

Z1 IR

Z3 IR

rLead/rDock

RS232

USB

TRIG Z1

TRIG Z2

TRIG Z3

SIRIUS

DAB

ETHERNET

TRIG Z1

TRIG Z2

TRIG Z3

rLead/rDock

RS232

USB

Z2 IR

IR OUT

Z1 IR

Z3 IR

is input is intended for use with an IR receiver in

Zone3 to allow remote control of the unit from a third

room.

IR OUT

is output is an electrical combination of the Z1 (or

front panel) + Z2 + Z3 infra-red signals above. It can be

used to drive external IR emitters or can be connected

directly to other Arcam equipment which have an IR

input. is function can be useful as an IR ‘repeater’

so that someone in any of the zones can control the

functions of a CD player in the main zone, for example.

Tip is the modulated electrical IR signal, sleeve is

ground.

A supplier of infra-red receivers and emitter accessories

and systems is Xantech. See www.xantech.com for

more information, or ask your Arcam dealer.

NOTE

e IR inputs on the unit are designed for

modulated signals. If the external IR receiver

demodulates the IR signal, it will not work. Also the

unit does not provide power for external receivers

on the IR jack, therefore an external power source

will be required.

TRIG Z3

Use for remotely turning on and o power amps or

source equipment for Zone3. On = 12V, O = 0V.

NOTE

Sockets with the prex ‘Z2’ or ‘Z3’ refer to

connections used in multi-room installation. For

more information on these connectors, see page 54.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Arcam AV888 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Arcam AV888

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info