Bedienungsanleitung Arcam AV888 (Seite 56 von 74) (Englisch)

482343

Zoom out

Zoom in

Vorherige Seite

1/74

Nächste Seite

E-54

Zone2 and 3 control outputs

e AVR500, AVR600 and AV888 also allow remote

control from remote zones.

Z2 IR and Z3 IR

is allows the AVR500/AVR600/AV888 to be

controlled remotely from Zone2 (or Zone3) via Infra-

red remote control. Connect a remote IR receiver in

Zone2 (or Zone3) to allow control of the AVR500/

AVR600/AV888 from these listening/viewing areas.

For more information on remote IR receivers, see ‘Z1 IR’

on page 17.

TRIG Z2 and TRIG Z3

is allows the AVR500/AVR600/AV888 to remotely

switch on devices in Zone2 (or 3) when the appropriate

Zone is selected. For example you could set your

television in Zone2 to switch on when ‘Zone2’ is

selected on AVR500/AVR600/AV888.

For more information on triggers, see ‘Trigger

connectors’ on page 17. Please note that not all AV

devices have this feature, nor are triggers essential for

listening and viewing in a separate zone.

multi-room

set up

e AVR500, AVR600 and AV888 allow independent

routing and control of analogue audio, Composite and

S-Video to a separate set of equipment, typically used

for a second living space, e.g., bedroom or lounge. e

AVR600 and AV888 also allow a copy of the Zone2

analogue audio to be routed to and controlled in a third

living space, Zone3.

e connection guide on the facing page shows how the

AVR600 or AV888 is normally connected in a multi-

room installation.

Zone2

Zone2 receives only signals obtained by the AVR500,

AVR600 or AV888 from the analogue audio, Composite

and S-Video inputs. e analogue inputs are required

because there is no analogue-to-digital, digital-to-

analogue or DSP processing available for Zone2 signals

– the unit only converts video formats for Zone1.

For this reason, we recommend that in addition to any

digital connections, the Composite and/or S-Video

outputs from your source devices are connected to the

AVR500, AVR600 or AV888.

Video outputs

e Z2 S-Video and/or Composite output connectors of

the AVR500/AVR600/AV888 should be connected to

the analogue video inputs (usually labelled SVIDEO IN or

COMPOSITE VIDEO IN) of the display device in Zone2.

If you wish to make an HDMI connection to Zone 2,

you must accept the limitations of the AVR500/AVR600/

AV888 video processing system.

HDMI OUT 1 and OUT 2 both carry the same signals (as

there is only one video processing engine) and are

primarily intended for use in Zone 1. Full HDMI video

functionality in Zone 2 can only be achieved if Zone 1 is

not being used at the same time.

If Zone 1 is being used at the same time as Zone 2,

Zone 2 must follow the Zone 1 source selection if you

wish to receive HDMI signals in Zone 2. Zone 2 must

also be the same video resolution as Zone 1. If you wish

to watch a dierent source in Zone 2 than is currently

showing over HDMI in Zone 1, Zone 2 will be forced to

use the analogue video connections into and out of the

AVR500/AVR600/AV888.

Due to the complications of using HDMI in Zone 2

we recommend the use of analogue video connections

instead, particularly as it is not possible to apply audio

lip sync to Zone 2 audio to compensate for video

processing delays.

SIRIUS

DAB

ETHERNET

Z2 IR

IR OUT

Z1 IR

Z3 IR

rLead/rDockRS232

USB

TRIG Z1

TRIG Z2

TRIG Z3

Audio outputs

e Z2 OUT, R and L phono sockets should be connected

to the analogue audio inputs (Usually labelled

ANALOGUE AUDIO IN) of the Zone2 display device, or

to the inputs of an additional stereo power amplier in

Zone2 (for example, the Arcam P38).

Zone3 (AVR600/AV888 only)

A line-level signal from the stereo analogue audio is

available for Zone3. is is a copy of the Zone2 audio

signal, but has its own independent volume control.

Audio outputs

e Z3 OUT, R and L phono sockets should be connected

to the inputs of an additional stereo power amplier in

Zone3 (for example, the Arcam P38).

888

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Arcam AV888 Seite 56

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Arcam AV888

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info