578729
5
Zoom out
Zoom in
Vorherige Seite
1/69
Nächste Seite
E-5E-4
English
installation
Placing the unit
< Place the CD player on a level, rm surface,
avoiding direct sunlight and sources of heat or
damp.
< Do not place the CD player on top of an
amplier or other source of heat.
< Do not place the CD player in an enclosed space
such as a bookcase or closed cabinet unless
there is good provision for ventilation. e CD
player is designed to run warm during normal
operation.
< Do not place any other component or item on
top of the CD player as this may obstruct airow
around the unit, causing the CD player to run
hot.
< Make sure the remote-control receiver (next to
the display on the front panel) is unobstructed,
or remote control will be impaired.
< Do not place your record deck on top of this
unit. Record decks are very sensitive to the noise
generated by mains power supplies which will be
heard as a background ‘hum’ if the record deck
is too close.
Power
e CD player is supplied with a moulded mains plug
already tted to the lead. Check that the plug supplied
ts your supply – should you require a new mains lead,
please contact your Arcam dealer.
If your mains supply voltage or mains plug is dierent,
please contact your Arcam dealer immediately
Push the IEC plug end of the power cable into the
socket on the back of the CD player, making sure that it
is pushed in rmly. Plug the other end of the cable into
your mains socket and, if necessary, switch the socket
on.
The remote control and trigger
inputs
e REMOTE IN input can be used to pass RC5 codes
to the CDS27 if it is installed in a position or system,
where infrared cannot be used. If this is required, please
contact your dealer for further information.
NOTE
< e remote control input requires a mono
3.5mm jack, with the tip active and the
sleeve grounded.
< e remote control signals must be in
modulated RC5 format (at 36kHz), with a
voltage level of between 5V and 12V.
e 12V TRIGGER IN input can be used to switch the
CDS27 into and out of standby. Connecting the trigger
output of your Arcam amplier (or other compatible
device), will cause the CDS27 to come out of standby
automatically when the amplier is switched on,
returning to standby when the amplier is switched
o. Please see your amplier handbook for further
information.
In normal use there is no need to make any connections
to these inputs.
e RS232 input is for optional connection to a home
automation system or computer. Various third-party
systems are available providing sophisticated control
over all your entertainment devices using touch screens
etc. Contact your dealer or installer for further details.
e technical details of the remote control protocol
are available from Arcam on request (email support@
arcam.co.uk).
Interconnect cables
We recommend the use of high-quality screened cables
that are designed for the particular application. Other
cables will have dierent impedance characteristics
that will degrade the performance of your system (for
example, do not use cabling intended for video use to
carry audio signals). All cables should be kept as short
as is practically possible.
It is good practice when connecting your equipment to
make sure that the mains power-supply cabling is kept
as far away as possible from your audio cables. Failure
to do so may result in unwanted noise in the audio
signals.
Contents
safety guidelines ����������������������������������������������������������������������������������������������������������������������������������������E-2
Important safety instructions ����������������������������������������������������������������������������������������������������������������������������������������������������� E-2
Safety compliance ��������������������������������������������������������������������������������������������������������������������������������������������������������������������������� E-2
welcome �������������������������������������������������������������������������������������������������������������������������������������������������������E-3
installation ���������������������������������������������������������������������������������������������������������������������������������������������������E-5
Placing the unit �������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� E-5
Power ��������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� E-5
The remote control and trigger inputs ������������������������������������������������������������������������������������������������������������������������������������ E-5
Interconnect cables ������������������������������������������������������������������������������������������������������������������������������������������������������������������������ E-5
CDS27 connections ������������������������������������������������������������������������������������������������������������������������������������E-6
Network connection ���������������������������������������������������������������������������������������������������������������������������������������������������������������������� E-7
USB connection ������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� E-7
Making audio connections ���������������������������������������������������������������������������������������������������������������������������������������������������������� E-7
Playable discs ������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������ E-7
Supported Media ���������������������������������������������������������������������������������������������������������������������������������������������������������������������������� E-7
basic operation �������������������������������������������������������������������������������������������������������������������������������������������E-8
remote control ��������������������������������������������������������������������������������������������������������������������������������������������E-9
settings menus ���������������������������������������������������������������������������������������������������������������������������������������� E-11
Navigating the menus ����������������������������������������������������������������������������������������������������������������������������������������������������������������� E-11
troubleshooting �������������������������������������������������������������������������������������������������������������������������������������� E-12
specications ������������������������������������������������������������������������������������������������������������������������������������������� E-13
Radio interference�������������������������������������������������������������������������������������������������������������������������������������������������������������������������E-13
Laser radiation �������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� E-13
software licencing ����������������������������������������������������������������������������������������������������������������������������������� E-14
product guarantee ���������������������������������������������������������������������������������������������������������������������������������� E-16
Worldwide Guarantee������������������������������������������������������������������������������������������������������������������������������������������������������������������E-16
Claims under guarantee �������������������������������������������������������������������������������������������������������������������������������������������������������������E-16
Problems? �����������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������E-16
On-line registration ����������������������������������������������������������������������������������������������������������������������������������������������������������������������E-16
5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Arcam CDS27 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info