Bedienungsanleitung Arcam CDS27 (Seite 7 von 69) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

578729

Zoom out

Zoom in

Vorherige Seite

1/69

Nächste Seite

E-9E-8

English

basic

operation

e CDS27 is supplied with the CR902 remote control.

Using the remote control

Please keep in mind the following when using the

remote control:

< Ensure there are no obstacles between the

remote control and the remote sensor on the

front panel. e remote has a range of about

7metres. (If the remote sensor is obscured, the

IR in remote control input jack on the rear panel

is available. Please consult your dealer for further

information.)

< Remote operation may become unreliable if

strong sunlight or uorescent light is shining on

the remote sensor of the unit.

< Replace the batteries when you notice a

reduction in the operating range of the remote

control.

Inserting batteries into the remote control

1. Open the battery compartment on the back of

the handset.

2. Insert two ‘AAA’ batteries according to the

diagram on the battery cover casing.

3. Slide the battery cover casing back into position

and lock it closed with a click.

remote

control

NOTE

< Incorrect use of batteries can result in hazards

such as leakage and bursting.

< Do not mix old and new batteries together.

< Do not use non-identical batteries together

– although they may look similar, dierent

batteries may have dierent voltages.

< Ensure the plus (+) and minus (–) ends of

each battery match the indications in the

battery compartment.

< Remove batteries from equipment that is not

going to be used for a month or more.

< When disposing of used batteries, please

comply with governmental or local

regulations that apply in your country or area.

The CR902 remote complies with Part 15

of the FCC rules

is equipment has been tested and found to comply

with the limits for a class B digital device, pursuant

to part 15 of the FCC Rules. ese limits are

designed to provide a reasonable protection against

harmful interference in a residential installation.

is equipment generates, uses, and can radiated

radio frequency energy and if not installed and

used in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to radio

or television reception, which can be determined

by turning the equipment o and on, the user is

encouraged to try to correct the interference by one

or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and

receiver.

Connect the equipment into an outlet or a circuit

dierent from that to which the receiver is

connected.

Consult the dealer or an experienced audio

technician for help.

AUDIO

SACD

FM MONO P/TUNE

STORE

INFO

CR902

RTN

During playback

Scan

Press

on the front-panel or remote control

to scan forwards or backwards, at x4 normal playback

speed. To resume normal playback, press PLAY.

Skipping chapters/tracks

To skip tracks, press

When skipping back, the rst button press takes you to

the beginning of the current track. Pressing the button

again takes you to the start of the previous track.

Pausing playback

Press

;

on the front panel or

;

on the remote

control to pause playback. To resume playback, press

;

on the front panel or

on the handset.

Stopping playback

Press the

button on the front panel or

on the

remote control to stop playback.

Introduction

‘Basic operation’ explains how to play audio discs,

network content and audio les stored on USB media.

Note that it may be necessary to congure your player

correctly for your system before optimum – or any–

playback can be achieved. Player conguration is

described beginning on page 11.

Switching on

Switch the unit on by pressing the POWER button. e

status LED glows green when the unit is powered up

and red when in standby mode. Standby mode may be

entered using the standby button on the remote control

and exited using either the same button, or the

key on the front panel. If the POWER button is pressed

(or power is removed) whilst in standby, the unit will

enter standby mode when power is re-applied.

Note that the remote control sensor is located to the

right-hand side of the display window. Do not obstruct

this or the remote control will not work.

Playing a disc

Press

on the front panel (or

on the handset)

and place the disc on the tray, with the playback side

facing down (some discs are double sided, in which

case the side labelled ‘side A’ should face up to play

sideA).

Press

on the front panel to close the tray. e disc

loads aer a pause of a few seconds.

A disc may take some time to load once the tray is

closed. When the ‘Disc Autoplay’ setting is set to On

(the default setting), playback starts automatically. (For

details, refer to ‘Disc Auto Playback’ on page 11).

For discs that do not play automatically, press

;

the front panel or press

on the remote control.

Playing from the network

Ensure the CDS27 is connected to your local network.

Select ‘Media Browser’ from the home screen, the user

will be presented with a list of devices available for

browsing. Navigate the available libraries using the

keys on the remote.

Network music playback may also ne controlled from

your computer, phone or mobile device using your

favourite UPnP control point application.

Pressing OK or

on a highlighted audio le will access

the le for playback. Playback will continue through all

subsequent tracks in the playback directory.

Playing from USB

Connect your USB device to the USB socket to the rear

of the CDS27. Aer the device has been recognised

select ‘Media Browser’ from the home screen, then

choose the ‘USB’ option from the media list.

Navigate directions using the

keys on

the remote and begin playback of a highlighted audio

le by pressing OK,

. Playback will continue

through all subsequent tracks in the playback directory.

Arcam CDS27 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info