Bedienungsanleitung Arcam DiVA AVR200 (Seite 8 von 19) (Englisch)

578767

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

AVR200

Setting up

Using the On Screen Display (OSD)

The easiest way to set up the AVR200’s multi-channel audio and

video options is through its On Screen Display (OSD).

To enter the OSD, ensure that you have a TV connected and

press any of the arrows on the remote control’s cursor pad.

To navigate from the ﬁ rst (i.e. Setup) page, use the

•

and

•

arrows to highlight a line. To enter a highlighted page, press OK.

To leave the OSD, highlight ‘EXIT’ and press OK.

Once on a page, use the

•

and

•

arrows to move to a line

and the

•

and

•

arrows to change an option. Once you are

happy with the settings, highlight ‘SAVE AND EXIT’ and press OK

to keep them in memory. If you are unsure about the changes,

or you have entered the page accidentally, highlight ‘DO NOT

SAVE AND EXIT’ and press OK and any changes on that page

are ignored.

Setup page

The Setup page forms the index to the OSD. To navigate from

here, use the cursor pad on your remote control.

Input settings page

AUDIO Identiﬁ es the active audio source (e.g. CD)

VIDEO Identiﬁ es the active video source (e.g. DVD)

MODE Identiﬁ es the surround mode associated with

the current input (Dolby Digital, DTS, Dolby

Pro Logic II Movie, Dolby Pro Logic II Music,

Dolby Pro Logic II Panorama, Dolby Pro Logic II

Matrix, Dolby Pro Logic, Hall effect or Stereo)

DYNAMIC RANGE

A compressed dynamic range is useful for low

level (night time) listening. For Dolby Digital

sources, the dynamic range has options of

100%, 75%, 50% or 25%

CENTRE WIDTH (Dolby Pro Logic II Music Mode only)

Allows centre-channel sounds to be positioned

between the centre speaker and the left/right

speakers over a range of eight steps. Step ‘3’

uses a combination of all three front speakers

to give the best vocal imaging and most

seamless soundstage and is recommended for

most recordings. Step ‘0’ places all centre

sound in the centre speaker. Step ‘7’ places all

centre sound equally in the left/right speakers,

as in conventional stereo.

1 INPUT SETTINGS

2 CHANNEL BALANCE

3 CHANNEL DELAYS

4 SPEAKER SETTINGS

5 EXIT

SETUP

1 INPUT SETTINGS

2 CHANNEL BALANCE

3 CHANNEL DELAYS

4 SPEAKER SETTINGS

5 EXIT

SETUP

AUDIO = DVD

VIDEO = DVD

MODE = DOLBY DIGITAL

DYNAMIC RANGE = N/A

CENTRE WIDTH = 3

DIMENSION = 0

DO NOT SAVE AND EXIT

SAVE AND EXIT

INPUT SETTINGS

NOTE: In some cases you may ﬁ nd that the OSD is not still

or that it ‘rolls over’ your screen. (You may also notice this

effect when the volume bar is shown on screen.) If this is

the case, you will need to switch the video system being

used by the AVR200.

To do this, ﬁ rst exit the OSD by highlighting

EXIT and press

OK. Press and hold the STORE button on the front panel of

the AVR200 then toggle between the systems shown in the

display area by pressing the SAT button – NTSC (used in

North America) or PAL (used in most of Europe) – until the

correct system is selected.

centre

front

left

front

right

20.8° 20.8°

28°

36°

54°

62°

69.8°

28°

36°

54°

62°

69.8°

Setting options for CENTRE WIDTH

DISPLAY EFFECT

Off No Centre spreading

1 20.8°

2 28°

3 36°

4 54°

5 62°

6 69.8°

7 Phantom Centre

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Arcam DiVA AVR200 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info