Bedienungsanleitung Arcam DiVA AVR200 (Seite 9 von 19) (Englisch)

578767

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

AVR200

English

1 INPUT SETTINGS

2 CHANNEL BALANCE

3 CHANNEL DELAYS

4 SPEAKER SETTINGS

5 EXIT

SETUP

LEFT : 0dB

CENTER : 0dB

RIGHT : 0dB

REAR L : 0dB

REAR R : 0dB

SUB : 0dB

DO NOT SAVE AND EXIT

SAVE AND EXIT

CHANNEL BALANCE

NOTE: The test tone generates a noise which may not be

heard through a subwoofer. To set your sub to a suitable

level, turn off the test tone and experiment with the trim

while playing a piece of music or a movie you are familiar

with. There is no right or wrong level for the sub: simply ﬁ nd

the balance that is best for you.

1 INPUT SETTINGS

2 CHANNEL BALANCE

3 CHANNEL DELAYS

4 SPEAKER SETTINGS

5 EXIT

SETUP

CENTER 0ms

REAR 0ms

DO NOT SAVE AND EXIT

SAVE AND EXIT

CHANNEL DELAYS

CENTER 3ms

REAR 6ms

DO NOT SAVE AND EXIT

SAVE AND EXIT

CHANNEL DELAYS

NOTE: It is not necessary to adjust delay times separately

for a DTS (Digital Theater Systems) source.

DIMENSION (Dolby Pro Logic II Music Mode only) Allows

the gradual adjustment of the soundﬁ eld either

towards the front or the rear. This can help

achieve the desired balance from all the

speakers with certain recordings that may

contain either too much or too little spatial

effect. Step ‘0’ is the recommended setting,

which has no effect on the sound. Steps

‘+1’, ‘+2’ and ‘+3’ gradually move the sound

forward, and steps ‘–1’, ‘–2’ and ‘–3’ move the

sound towards the surrounds.

Channel balance page

From the Channel balance page, you can trim the level of

each individual loudspeaker connected to the AVR200. Due to

the different performance characteristics or positioning of each

loudspeaker they may need to be set to different levels to

provide a balanced sound from the listening position. To help set

this balance, the AVR200 can generate a test tone that plays an

identical signal through each channel in turn. Trim the balance

of each speaker in turn until they all appear to produce the

same volume.

Once the channel balance page is shown in the OSD, press

the

TEST button on the remote control to start the test tone.

Make sure that either Dolby Digital, Dolby Pro Logic or Dolby

Pro Logic II is selected, and that the volume on the AVR200

is set sufﬁ ciently high for the tone to be heard. The test tone

automatically cycles through each speaker channel until the

TEST button is pressed a second time.

Each loudspeaker can be trimmed between +10dB and –10dB.

You can return to the Channel balance page at any time (without

ﬁ rst entering the OSD) by pressing the

TEST button on the

remote control. Press TEST again to exit this page.

Channel delays page

For best results in a surround sound system, the sound from

all loudspeakers should reach the listener at the same time. To

help achieve this the AVR200 can add slight delays to certain

channels when in Dolby Digital or Dolby Pro Logic modes.

When playing a Dolby Digital source you can set a delay for the

centre channel of between 0 and 5ms and a delay for the rear

channels of between 0 and 15ms.

The method of calculating these delay times is described

overleaf.

Setting options for DIMENSIONS

DISPLAY EFFECT

–3 MAX SURR Most surround

–2

–1

0 Neutral

+3 MAX CENTRE Most centre

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Arcam DiVA AVR200 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info