Bedienungsanleitung Arcam DiVA AVR280 (Seite 22 von 38) (Englisch)

578769

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

AVR280

Input selection

To select a particular source, press the corresponding button on the front panel or on the remote control.

There are eight inputs available: DVD, Sat, AV, AUX, VCR, Tape, CD and MCH (DVD-A multi-channel). In

addition, AM and FM radio reception can be selected from the built-in tuner. Any picture signal associated

with the selected input is switched to the monitor output.

On selecting a source, the AVR280 will attempt to use the digital input in preference to an analogue

input, assuming a digital signal is detected for the source. If you want to override the digital input and

select the analogue input instead, however, this can be achieved by pressing and holding the button for

the selected source for at least two seconds.

The processing mode and ‘Stereo Direct’ functions are remembered and recalled for each input. The

digital input and high quality video input associated with each source may be congured in the device

menus.

The DVD-A input is intended for direct analogue pass-through of DVD Audio or SACD surround sources.

Apart from volume control and level trim, no processing is performed on this input.

Tape operation

The TAPE button selects the audio from a cassette deck connected to the TAPE IN phono sockets of the

AVR280.

Pressing the TAPE button will select audio from the tape input; the TAPE LED will illuminate, together

with the LED of the previously selected input. Illuminating the tape and source LEDs indicates that the

tape loop is active and indicates the source that will be recorded.

Example:

If you want to record from the CD input:

Select the CD input;

Press the TAPE button – you can now listen to the sound returned from the recording device. In

the case of a three-head cassette deck, this will be the audio as recorded onto the tape.

Note that selecting a different source from CD will cause the recording to change to this new source.

VCR/AUX Operation

The AVR280 has VCR and AUX record loops for audio and video (Composite and S-video only). These

carry the audio and video (if any) from the currently-selected source. The VCR output is muted if VCR is

the selected source; the AUX output is muted if AUX is the selected source.

Example:

If you want to record the SAT input:

Select the SAT input.

Press the button labeled ‘record’ (or similar) on your VCR/AUX to begin recording.

Note that, if you select a different source from SAT, the recording changes to this new source.

Stereo Direct

To listen to a pure analogue stereo input, press the DIRECT button. The Direct mode bypasses

automatically all processing and any surround functions. In Direct mode, digital processing is shut down

to improve the sound quality by reducing the digital noise within the AVR280 to an absolute minimum.

The LED above the DIRECT button on the front panel will illuminate to indicate this mode.

Important: When ‘stereo direct’ mode is enabled, bass management is disabled. For this reason,

‘stereo direct’ mode is not recommended in systems comprising small ‘satelite’ speakers, as the full-

frequency information that would be directed to these units may cause damage to the speaker.

Zone 2

Pressing the ZONE 2 button allows both the volume and the source being viewed in Zone 2 to be changed

from the main zone. While in this ‘Zone 2’ mode, the LED above the Zone 2 button is illuminated.

When rst pressed, the text ZONE2 SRC is displayed on the front panel (where ‘SRC’ indicates the source

being viewed in Zone 2). Pressing the source buttons on the front panel while in this state changes the

source routed to Zone 2; moving the volume knob adjusts the Zone 2 volume.

To exit this state, press ZONE 2 a second time.

Headphones

To use headphones with the AVR280, plug the headphones into the socket on the left hand side of the

front panel.

When headphones are plugged into the headphones socket the main output is muted.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Arcam DiVA AVR280 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info