Bedienungsanleitung Arcam DiVA P85 (Seite 4 von 14) (Deutsch, Englisch, Französisch)

578760

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

A85/P85

Installation: A85 integrated ampliﬁ er

Positioning the unit

Place your ampliﬁ er on a level, ﬁ rm surface.

Avoid placing the unit in direct sunlight or near sources of heat

or damp.

Ensure adequate ventilation. Do not place the unit in an

enclosed space such as a bookcase or cabinet as both of

these will impede air ﬂ ow through the ventilation slots.

Connecting to loudspeakers

You can connect one or two pairs of loudspeakers to your

ampliﬁ er, provided each pair is rated between 8–16Ω. If one or

both pairs have an impedance of less than 8Ω, the combined

load on the ampliﬁ er falls below 4Ω and could cause an

overload. If so, the overload protection circuit engages and the

ampliﬁ er will not work.

To connect one pair of loudspeakers, use the

SP1 terminals.

SP1 and SP2 terminals

Both sets of loudspeaker terminals can be switched off by

pressing the MUTE button on the remote control. To switch SP1

and SP2 independently, use the front panel switch

(see

page 6) or the remote control (see page 9).

Your ampliﬁ er is ﬁ tted with loudspeaker terminals to BFA

(British Federation of Audio) standard speciﬁ cation.

BFA loudspeaker terminals

The terminal will accept spade terminals, bare wires or a

BFA plug. BFA plugs are available from your Arcam dealer. To

connect a bare wire or spade terminal, unscrew the red (or

black) part of the loudspeaker terminal ﬁ rst.

Insert the wire or spade terminal and screw it back up.

CAUTION: Do not over tighten the loudspeaker terminals or

use a wrench, pliers, etc., as this could cause damage to the

terminals which will not be covered under warranty.

Connect the right speaker to the terminals on the back of

your ampliﬁ er marked

R and the left speaker to the terminals

marked L.

Connect your loudspeakers so that the red (positive/+) terminal

on each loudspeaker is connected to the red (positive/+)

terminal on the ampliﬁ er. Your loudspeaker cables may be

marked to show polarity (negative/– and positive/+), if not, then

the positive terminal can usually be identiﬁ ed by a ridge or

coloured marking.

Now connect your loudspeakers’ black (negative/–) terminals to

the black (negative/–) terminals on the ampliﬁ er.

Ensure that no stray strands of inner wires are allowed to touch

another cable or the ampliﬁ er’s casing. This can cause a short

circuit and damage your ampliﬁ er!

Wiring your loudspeakers

+ –

PHONO

+ –

SP1

SP2

POWER INLET

PRE OUTPWR IN

6 8 9 bk bl bm bn bo bp54 bq1

4 – 16 OHMS

VOLTAGE

SELECT

230V

RECORD

OUT

PLAY

TAPE 1

RECORD

OUT

PLAY

VCR/TAPE 2 DVD AV TUNER CD AUX

INTEGRATED

PRE/PWR

REMOTE

TRIG

OUT

7br

Arcam A85 amplifier

+ –+ –

Right

speaker

–

Left

speaker

A85/P85 multi.id 03/29/01, 3:34 PM4

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Arcam DiVA P85 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info