Bedienungsanleitung Arcam DiVA P85 (Seite 5 von 14) (Deutsch, Englisch, Französisch)

578760

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

A85/P85

English

Connecting to a power supply

Wrong plug?

Check that the plug supplied with the unit ﬁ ts your supply and

that your mains supply voltage agrees with the voltage setting

(115V or 230V) indicated on the rear panel of the unit

before plugging in.

If your mains supply voltage or mains plug is different, consult

your Arcam dealer or Arcam Customer Support on +44

(0)1223 203203.

The product must be earthed.

Mains lead

The appliance is normally supplied with a moulded mains plug

already ﬁ tted to the lead. If for any reason the plug needs to

be removed, it must be disposed of immediately and securely,

as it is a potential shock hazard when inserted into the mains

socket. Should you require a new mains lead, contact your

Arcam dealer.

Plugging in

Push the plug (IEC line socket) of the power cable supplied with

the unit into the socket (POWER INLET)

in the back of the

unit. Make sure it is pushed in ﬁ rmly.

Put the plug on the other end of the cable into your power

supply socket and switch the socket on.

Standby power

For remote standby operation, the ampliﬁ er’s control power

supply is kept powered up all the time the unit is connected to

the mains supply. The front panel power switch powers down

all other circuitry. Power consumption in this mode is less than

2W.

This means that even though the power switch is off, it may be

possible to hear a slight residual hum coming from the mains

transformer inside the ampliﬁ er. This is perfectly normal. If the

unit is to be left unused for an extended period, we recommend

that it is disconnected from the mains supply by switching it

off at the wall socket.

Connecting to other equipment

The use of high quality interconnect cables to and from your

ampliﬁ er is recommended to ensure the best sound quality.

Sockets marked

L (and R) on your ampliﬁ er should only be

connected to sockets marked L (and R) on other equipment. All

the line inputs have the same sensitivity and may be used with

equipment other than that labelled, if needed.

TAPE1/RECORD OUT

– Connect these output sockets

to the input sockets of your cassette deck (usually labelled

RECORD).

TAPE1/PLAY IN

– Connect these input sockets to the

output sockets of your cassette deck (usually labelled PLAY).

If you do not have a cassette deck you can use this input for

other (line level) equipment, such as a CD player, tuner, VCR,

etc., but not a turntable.

VCR/TAPE2 RECORD OUT

– These output sockets can

be connected to the input sockets of VCR/second recorder

(usually labelled RECORD).

VCR/TAPE2 PLAY IN

– Connect these input sockets

to the output sockets of your VCR/second recorder (usually

labelled PLAY). Alternatively, you can use this input for other

(line level) equipment such as a CD player, tuner, etc., but not

a turntable.

DVD

– Connect this input to the audio outputs of a DVD

player.

– Connect this input to audiovisual equipment such as a

VCR, laserdisc player, satellite or Nicam tuner.

TUNER

– Connect this input to the audio outputs of your

radio tuner.

– Connect this input to the audio outputs of your CD

player or DAC (digital to analogue converter).

AUX

– Connect this input to the audio outputs of any unit

with a line level output, e.g. tape deck, tuner etc.

NOTE: The AUX inputs must not be used if the phono module

is ﬁ tted. When this is ﬁ tted AUX becomes an output carrying

the equalised phono signal at line level.

PHONO

– As standard, phono inputs are blanked. Phono

inputs are provided on a separate plug-in module which your

Arcam dealer or distributor can supply and ﬁ t. This module

is compatible with most high output moving coil and moving

magnet cartridges (MM) and low output moving coil cartridges

(MC). MM or MC is selected via the MM/MC back panel switch.

Phono earth terminal – For connecting your turntable earth

lead (if ﬁ tted). Note that this terminal must not be used as a

safety earth.

TRIG OUT and REMOTE IN

(12V in and out) – These

connections are for use in multi-room installations. In normal

use there is no need to make any connections to these

sockets. If you are bi-amping with a power ampliﬁ er and wish to

power both units on or off simultaneously, see page 11.

Pre/power ampliﬁ er connections

PWR IN

– To use your integrated ampliﬁ er as a power

ampliﬁ er, connect the output of your pre-ampliﬁ er to the PWR IN

sockets.

Press in the

PRE/PWR switch

on the rear panel to

select separate pre-amp/power amp mode. Under these

circumstances your A85 has exactly the same speciﬁ cation and

performance as a power ampliﬁ er (see page 8).

PRE OUT

– To use your integrated ampliﬁ er as a pre-

ampliﬁ er, connect the PRE OUT sockets to the input sockets

of your power ampliﬁ er. With a power ampliﬁ er of the correct

gain (e.g. the P85 power ampliﬁ er) you can bi-amplify (‘bi-amp’)

suitable loudspeakers, giving signiﬁ cant improvements in sound

quality (see page 12).

A85/P85 multi.id 03/29/01, 3:34 PM5

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Arcam DiVA P85 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info