Bedienungsanleitung Arcam dv 139 (Seite 12 von 26) (Englisch)

138744

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

DV139

E-12

Conguring your DVD player

Introduction

This section of the document describes the use of the ‘Set-up’ menu, which is used to congure your

player for your system and your personal preferences.

Obtaining a picture

To view the Set-up menu for the initial conguration, we recommend the

use of the composite video output to connect to your display device. This

is because the high quality video output has several display modes and

may be incompatible with your display device in its default conguration.

Ensure that your display device is switched on and that you have

selected the correct video input. You should see the image shown on the

right. This is the image that the DVD player gives whenever there is no

disc playing.

NOTE: To protect your screen from damage caused by persistent

static images, a ‘screen saver’ facility activates after a few minutes

of inactivity. When this occurs, a small ARCAM logo moves around

the screen. To reset the image, press the STOP button on the

player or on the remote control.

Using the Set-up menus

Your DV139 has two different set-up menus:

The Set-up menu allows conguration of all aspects of your DVD player. Congurable items and

their potential values are described on the following pages.

The Display set-up menu is a series of video test patterns with instructions that will allow you to

congure your display optimally for your DVD player.

The Set-up menu

The Set-up menu comprises six pages of options. The tabs on the left side of the screen show the pages

available, indicating the nature of the items on each page. To change between pages, move the menu

highlight to the appropriate tab and press

To change an item rst use the UP/DOWN controls to highlight the item, then press OK to open the list of

options for the menu item. The current option for the menu item is indicated. The UP/DOWN controls can

be used then to select the new option and pressing OK conrms the new selection and closes the option

list. (If the item to be changed is controlled by a slider, press OK to activate the slider and OK again

when the desired value has been selected.)

Note that items that are not applicable currently (for example, the Pro Logic II settings when Pro Logic II

processing is switched off) are shown ‘greyed out’, and cannot be highlighted or changed.

To enter the Set-up menu, press the SETUP button on the remote control. Press SETUP for a second

time to close the menu.

The Display set-up menu

For optimum video performance it is necessary to congure your display for the video source – your DVD

player, in this case. A series of test patterns generated by your DVD player will allow you to optimise

colour balance, contrast, brightness and to centre your picture. Full instructions for each test pattern are

displayed on the screen before the test pattern is shown.

To enter the Display set-up menu, move the menu highlight to the ‘Display’ button, then press OK.

Press SETUP for a second time when you have nished.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Arcam dv 139 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info