Bedienungsanleitung Arcam Neo (Seite 6 von 88) (Deutsch, Englisch, Holländisch, Französisch)

578807

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

>60cm

15 –

40cm

40 – 60cm

2 – 3m

Speaker installation

The advice given here are general guidleines for speaker installation.

Refer to the documentation supplied with your speakers for more

precise positioning and installation information.

Positioning

As a rough guide, speakers should be placed on rigid stands at about

15–40cms from the rear wall and at least 60cms from any side wall.

Speakers should never be placed on the oor (unless they are oor-

standing speakers), or in corners.

The nal sound will depend on the acoustics of the listening room

and experimentation with speaker positioning is very worthwhile.

As a starting point, we suggest that the speakers are placed

2–3m apart with their backs 15cms from the rear wall.

Listening in a second room

Solo Neo provides two independent volume

controls, oering you the possibility of listening

to the same output in two dierent rooms of your house. To do this, you will require the

following:

< a power amplier (such as the Arcam P38) and speakers;

< suitable interconnect cables, such as those described above;

< a remote control receiver (optional), available from your Arcam dealer;

< a second Solo Neo remote control (optional), available from your Arcam

dealer.

Make the connections as follows:

1. Ensure that all equipment is switched o and disconnected from the mains

supply.

2. Connect the outputs of Solo Neo labelled ‘Zone 2’ to the audio inputs of the

power amplier using the interconnect cables.

3. Connect the speakers to the speaker terminals of the power amp. The speakers should

be connected in the same method as described in the panel on page 4, ‘Speakers’.

4. Plug the remote receiver from the second room into the connector labelled ‘In Zone 2’

on the rear of Solo Neo.

5. Reconnect the equipment to the mains supply and switch on. You should be able to

hear the output of Solo Neo in through the power amp. and control the volume using

the remote control.

Adjusting Zone 2 volume

Press and hold MENU on the front panel until ‘Z2 Vol’ is displayed, then use the volume

control to decrease/increase the Zone 2 volume. Press MENU again to exit.

Note that the second room is always muted when

Solo Neo is switched on – it must be unmuted

‘explicitly’ when required. This is to avoid

unexpected output in the remote location.

Speaker stands

The more rmly a speaker is held, the better it will sound. We

recommend the use of rigid metal stands of 40–60cms height.

Properly damped types that do not ‘ring’ when tapped with

a pencil (either by virtue of construction, or because they are

lled with dry silver sand) will bring out the best in a speaker.

Ensure that the stands and/or speakers do not wobble.

>60cm

15 –

40cm

40 – 60cm

2 – 3m

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Arcam Neo Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info