Bedienungsanleitung Arcam P777 (Seite 7 von 50) (Deutsch, Englisch, Holländisch, Französisch)

578808

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

E-7

English

Single wiring

If each speaker has more than one pair of connecting terminals, use the terminals labelled

LF or ‘Low Frequency’ for each speaker.

Connect the positive terminal of the right speaker connection on the amplier (coloured

red and labelled

+R) to the positive terminal of your right speaker. Similarly, connect the

negative terminal of the amplier (coloured black and labelled with R) to the negative

terminal of your speaker. Repeat the process for the le speaker, using the amplier

terminals labelled +L and L.

If your speakers support bi-wiring, then there is a strip of conductive metal on the

speakers connecting the low-frequency terminals to those for the higher-frequencies; this

MUST NOT BE REMOVED in a single-wired system.

Bi-wiring

Bi-wiring is performed in the same way as single wiring except that, for each speaker, a

pair of cables are used to connect the amplier to each speaker.

Follow the instructions given for single wiring; then perform the same actions, this time

connecting the upper set of speaker terminals on your amplier to the terminals labelled

HF or ‘High Frequency’ for each speaker. Please refer to the illustration.

Speakers that support bi-wiring have a strip of metal on the speakers connecting the low-

frequency terminals to those for the higher-frequencies; this MUST BE REMOVED in a

bi-wired system.

Bi-amping

Bi-amping requires the use of two amplier channels per speaker. Using this method will

prevent you from using seven surround speakers.

Connect two channels of the P777 with a phono cable between the

AUDIO OUT socket on

one channel to the AUDIO IN channel of another. One channel should then be connected to

the speakers as described for single wiring, with the exception that this channel should be

connected to the speaker terminals labelled HF or ‘High Frequency’. e second channel must

then be connected to the LF or ‘Low Frequency’ terminals, as in the diagram.

Note that the strip of metal on the speakers connecting the lower terminals to the upper

terminals MUST BE REMOVED. Failure to do so will result in damage to both ampliers,

which will not normally be covered under warranty.

Arcam recommends that the phono connections are use for bi-amping. If you prefer to use the

XLR connectors, use a Y-lead with one female XLR to two male XLRs, so that two amplier

channels may be fed from a single source. Contact your dealer if you need assistance.

Bi-wiring using one amplier

channel per speaker

Bi-amping using two amplier

channels per speaker

Single wiring speaker

connections

Outputs from multichannel pre-amp (e.g AV888)

Arcam P777

+Ð

IN OUT

+Ð

IN OUT

Arcam P777

+Ð

IN OUT

Arcam P777

SBR SR R C L SL SBL

+Ð

IN OUT

+Ð

IN OUT

+Ð

IN OUT

+Ð

IN OUT

+Ð

IN OUT

+Ð

IN OUT

+Ð

IN OUT

...etc...

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Arcam P777 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info