Bedienungsanleitung Arcam SoloSub (Seite 6 von 60) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

578740

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

E-7E-6

English

Wireless connection

To pair the unit with a Solo bar make sure

the unit is turned on at the power switch.

1. Press the button on the remote

control unit of the Solo bar followed

by until Speaker/EQ Setup appears

on the front display panel. Press

followed by again, until Sub Pairing

appears.

2. Press to start the pairing procedure.

e display will change to In Progress.

3. Position the INPUT selector on the rear

of the Solo sub to WIRELESS.

INPUT

LINE

WIRELESS

LFE

Solo sub and Solo bar positioning

100

115

125

140

160

X-OVER FREQ

0.3

0.5

0.7

0.9

1.1

1.3

1.5

X-OVER Q VOLUME

PHASE

0˚ 180˚

Solo sub recommended settings

For Phase settings, please refer to the

information on page9.

Wired connections

We recommend the use of high-quality

screened audio cables. Poor quality cables

will degrade the performance of your

system. All cables should be kept as short as

is practically possible.

It is good practice when connecting your

equipment to make sure that the mains

power-supply cabling is kept as far away as

possible from your audio cables. Failure to

do so may result in unwanted noise in the

audio signals.

Note: When connecting the Solo sub to

audio cables, or when moving it to a new

position, make sure that the unit is switched

off and disconnect the power lead. Failure to

do so may result in damage to both speaker

and amplifier.

Subwoofer/satellite system

is is a multi-speaker system comprising

of two or smaller satellite speakers (or a

soundbar) coupled with a subwoofer. e

satellite speakers are dened as ‘small’

and are responsible for reproducing

higher frequency audio signals; while the

subwoofer reproduces the lower frequencies

where the smaller speakers are not capable.

If your sound source has an output marked

SUB, SUBWOOFER or LFE, connect it to

the white L/LFE input on the back panel

of the Solo sub using an RCA connector at

each end.

L/LFE

SUB

Make sure the INPUT selector is set to LFE.

e LFE input bypasses the crossover in the

Solo sub, so the crossover frequency should

be set by the surround sound amplier. For

the crossover setting, please see the response

of your speakers which may vary from

around 70Hz for large satellites, to 150Hz

for small speakers. We recommend 85Hz as

a starting point if you are unsure.

INPUT

LINE

WIRELESS

LFE

Stereo system with no LFE

is is a typical two-channel system (such

as an Arcam stereo amplier). If your sound

source does not have SUB or LFE outputs,

connect the right and le channels of the

stereo pre-amp outputs (PRE OUT L and

PRE OUT R) to the red R and white L/LFE

inputs respectively.

L/LFE

PRE-OUT L

PRE-OUT R

Make sure the INPUT selector is set to LINE.

e crossover frequency on the Solo sub

should be adjusted to the low frequency roll

o of the main speakers (see the manual

for your speakers for this information). e

Q-control (XOVER Q) can be used to ne-

tune the integration of Solo sub and your

main speakers (see page8 for information).

INPUT

LINE

WIRELESS

LFE

4. Press and hold the WIRELESS button

on the rear of the Solo sub for about ve

seconds. e WIRELESS LED will start

ashing blue, signalling that the Solo sub

is in sync mode and searching for a

WIRELESS

PAIRING

PWR WIRELESS

5. If the the pairing procedure was

successful, the WIRELESS LED will glow a

constant blue and the Solo bar will display

Linked.

6. Once the pairing procedure is nished,

the Solo sub will always reconnect

whenever it is powered on or receives an

audio signal.

Note: Sync mode lasts for about 30seconds.

If no source is detected during this time, the

Solo bar will stop searching and the process

will need to be repeated.

After connecting

Turn the volume down to minimum on the

sound source amplier before switching it

on. Switch the source amplier on, select a

source signal, then gradually increase the

volume to the required listening level.

Note: The wired connection will not work if

the Solo sub has been previously linked to a

Solo sub using wireless connection. To disable

the wireless connection, place the Solo bar to

its factory default settings. Refer to the Solo

bar user manual for how to do this.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Arcam SoloSub Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info