578728

Arcam UDP411 Seite 8

8
Zoom out
Zoom in
Vorherige Seite
1/107
Nächste Seite
E-11E-10
English
e UDP411 is supplied with the CR301 backlit remote
control.
Using the remote control
Please keep in mind the following when using the
remote control:
< Ensure there are no obstacles between the
remote control and the remote sensor on the
front panel. e remote has a range of about 7
metres. (If the remote sensor is obscured, the IR
in remote control input jack on the rear panel is
available. Please consult your dealer for further
information.)
< Remote operation may become unreliable if
strong sunlight or uorescent light is shining on
the remote sensor of the unit.
< Replace the batteries when you notice a reduction
in the operating range of the remote control.
Inserting batteries into the remote control
1. Open the battery compartment on the back of the
handset.
2. Insert two ‘AAA’ batteries according to the
diagram on the battery cover casing.
3. Slide the battery cover casing back into position
and lock it closed with a click.
Backlight
A backlight comes on for ve seconds whenever a key
is pressed. is helps you use the handset in subdued
lighting conditions.
remote
control
NOTE
< Incorrect use of batteries can result in hazards
such as leakage and bursting.
< Do not mix old and new batteries together.
< Do not use non-identical batteries together
– although they may look similar, dierent
batteries may have dierent voltages.
< Ensure the plus (+) and minus (–) ends of
each battery match the indications in the
battery compartment.
< Remove batteries from equipment that is not
going to be used for a month or more.
< When disposing of used batteries, please
comply with governmental or local regulations
that apply in your country or area.
The CR301 remote complies with Part 15
of the FCC rules
is equipment has been tested and found to comply
with the limits for a class B digital device, pursuant to
part 15 of the FCC Rules. ese limits are designed
to provide a reasonable protection against harmful
interference in a residential installation. is
equipment generates, uses, and can radiated radio
frequency energy and if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not occur
in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment o and on, the user is encouraged to try
to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet or a circuit
dierent from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV
technician for help.
basic
operation
Introduction
‘Basic operation’ explains how to play a Blu-ray Disc
(BD), DVD, SACD, CD or other type of disc. Note that
it may be necessary to congure your player correctly
for your system before optimum – or any – playback can
be achieved. Player conguration is described beginning
on page E-16.
More sophisticated features – such as special playback
modes and programming jumps and playback sequences
– are described in the ‘advanced operation’ section, later
in this handbook.
Switching on
Switch the unit on by pressing the POWER button. e
status LED glows green when the unit is powered up and
red when in standby mode. e remote control is used
to enter and exit standby mode. If the POWER button is
pressed (or power is removed) whilst in standby, the
unit will enter standby mode when power is re-applied.
Note that the remote control sensor is located on the
right-hand side of the display window. Do not obstruct
this or the remote control will not work.
Loading a disc
Press
<
/
1
on the front panel (or
1
on the handset)
and place the disc on the tray, with the playback side
facing down (some discs are double sided, in which case
the side labelled ‘side A’ should face up to play side A).
Press
<
/
1
on the front panel to close the tray. e disc
loads aer a pause of a few seconds.
Playing a disc
A disc may take some time to load once the tray is
closed. When the ‘Optical Disc Autoplay’ setting is set to
On (the default setting), playback starts automatically.
(For details, refer to ‘Optical Disc AutoPlay’ on page
E-17).
If Autoplay is set to O, the player’s Main Menu will
appear on your TV. Use the cursor keys to select the disc
in MY MEDIA, then press
O
to start playback.
Some titles begin by displaying a menu. Select the menu
item ‘Play movie’ (or similar) using the cursor pad, then
press OK to start playback.
For discs that do not play automatically, press
4
/
;
on
the front panel or press
4
on the remote control.
Fast play
Press
8
or
7
on the front-panel or remote control to
play fast forwards or backwards. e following speeds
for fast playback are available: x2, x4, x8, x16 or x32
(depending on disc type). Press the button repeatedly
to cycle through the dierent speeds. To resume normal
playback speed, press PLAY.
Skipping chapters/tracks
To skip chapters (or tracks on a CD), press
/
or
0
.
When skipping back, the rst button press takes you to
the beginning of the current chapter. Pressing the button
again takes you to the start of the previous chapter.
Pausing playback
Press
4
/
;
on the front panel or
;
on the remote
control to pause playback. To resume playback, press
4
/
;
on the front panel or
4
on the handset.
Stopping playback
Press the
<
/
1
button on the front panel or
<
on the
remote control to stop playback.
When playing a BD/DVD, pressing
<
once performs
a ‘resume stop’. If you now press
4
, playback resumes
from the point it was stopped.
If you press
<
/
1
on the front panel or
<
on the remote
control twice, this is a ‘complete stop’, and playback
resumes from the beginning of the disc.
NOTE
When you press a button, if the unit does not accept
its operation, appears on the TV screen.
Invalid operation may also occur if:
< e region codes of the unit diers from that
of the disc, so playback is not allowed.
< e parental control is set to prevent
operation: see ‘Security/Parental Control’ on
page E-18.
< Some operations may be prohibited due to
disc manufacturer’s settings.
… 8 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Arcam UDP411 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info