Bedienungsanleitung Argo Charm Plus (Seite 25 von 30) (Englisch)

805093

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

56V 11/22

1. To prevent air leakage and spilling tighten all connecting nut of all

are tubes.

2. Connect the stop valve, charge hose, manifold valve, and vacuum

pump.

3. Fully open the handle Lo of the manifold valve and apply vacuum

for at least 15 minutes and check that the compound vacuum gauge

reads - 0.1MPa (-76cmHg).

4. After applying vacuum, fully open the stop valve with a hex wrench.

5. Check that both indoor and outdoor connections are free of air

leakage.

OUTDOOR CONDENSATION DRAINAGE

When the unit is heating, the condensing water and defrosting water can be out reliably

through the drain house.

Installation: install the outdoor drain elbow in Ф25 hole on the base plate, and joint

the drain hose to the elbow, so that the waste water formed in the outdoor unit can be

drained out to a proper plate.

CHECK AFTER INSTALLATION

• Electrical Safety Check

1. If the supply voltage is as required.

2. If there is any faulty or miss connection in each of the power, signal and grounding wires.

3. If the grounding wire of the air conditioner is securely grounded.

• Installation Safety Check

1. If the installation is secure.

2. If the water drain is smooth.

3. If the wiring and piping are correctly installed.

4. Check that no foreign matter or tools are left inside the unit.

5. Check the refrigerant pipeline is protected well.

• Leak test of the refrigerant

Depending on the installation method, the following methods may be used to check for suspect leak, on areas

such as the four connections of the outdoor unit and the cores of the cut-off valves and t-valves:

1. Bubble method: apply of spray a uniform layer of soap water over the suspected leak spot and observe

carefully for bubble.

2. Instrument method: checking for leak by pointing the probe of the leak detector according to the instruction to

the suspect points of leak.

Note: make sure that the ventilation is good before checking.

TEST OPERATION

• Test Operation preparation:

1. Verify that all piping and connection cables are well connected.

2. Conrm that the values at the gas side the liquid-side are fully open.

3. Connect the power cable to an independent power socket.

4. Install batteries in remote control.

Note: Make sure that the ventilation is good before testing.

• Test Operation method:

1. Turn on the power and push the ON/OFF switch button of the remote controller to start the air conditioner.

2. Select COOL, HEAT (not available on cool-only models), SWING and other operation modes with the remote

controller and see if the operation is ok.

Chassis

Outdoor drain elbow

Pressure gauge

Compound meter

-76 cmHg Manifold valve

Handle Hi

Charge hose

Handle Lo

Vacuum pump

Stop valve

(gas valve)

Stop valve

(liquid valve)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Argo Charm Plus Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Argo Charm Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info