Bedienungsanleitung Argo DD (Seite 12 von 16) (Englisch)

724566

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

5 - SPECIAL SETTINGS

SPECIAL SETTINGS THROUGH JUMPER

JP1:

Internal use. Do not change factory setting.

JP2 / JP3:

JP2 JP3 Description

Open Open Normal operation (factory setting)

Closed Open Setting “cooling only”.

If the heating mode is selected, the “wrong mode” error will be generated (see

auto-diagnosis table).

Open Closed Setting “heating only”.

If the cooling or dehumidifying mode is selected, the “wrong mode” error will

be generated (see auto-diagnosis table).

Closed Closed Automatic setting “cooling only” or “heating only” according to the outside

temperature.

Above 24°C the air conditioner is set to “cooling only”, under 20°C it is set to

“heating only”, between 20°C and 24°C it is left free.

If a mode that is opposite to the air conditioner setting is selected, the “wrong

mode” error will be generated (see auto-diagnosis table).

SPECIAL SETTINGS THROUGH REMOTE CONTROL UNIT

Limitation of the desired temperature range

The air conditioner is set by default to operate with a desired temperature range between 10°C and 32°C.

To limit this range between 16°C and 24°C in heating mode and between 22°C and 28°C in cooling or dehumidifying

mode, follow the procedure below:

1. Hold down the “FILTER” button for more than 7 seconds and release it. A number will appear on the remote control

screen.

2. Press the + or - keys until the number 12 is displayed.

3. Hold down the “FILTER” button for more than 7 seconds and release it by pointing the remote control at the air

conditioning receiver. An acoustic confirmation of 4 consecutive “beeps” will confirm the successful setting.

Note: on the remote control it will still be possible to select a temperature outside the range but the air conditioner will

limit it internally.

To disable the limitation of the desired temperature range, repeat the same procedure. An acoustic confirmation of 2

consecutive “beeps” will confirm that the original setting has been reset.

High wall installation setting

In case of high wall installation of the air conditioner, activate this setting to take into account the temperature stratification

during the heating mode.

Through this setting it is possible to select the temperature difference between the lower part of the room and the position

of the air conditioner in order to calibrate the reading of the air probe on the air conditioner. By default this difference is

set to 0°C (low wall installation). In case of high wall installation, it is recommended to set a difference of 3°C.

To change this parameter, follow the procedure below:

1. Hold down the “FILTER” button for more than 7 seconds and release it. A number will appear on the remote control

screen.

2. Press the + or - keys until the number 10 is displayed.

3. Hold down the “FILTER” button for more than 7 seconds and release it by pointing the remote control at the air

conditioning receiver.

4. Hold down again the “FILTER” button for more than 7 seconds and release it. The number 10 will appear on the

remote control screen.

5. Press the + or - keys to select the desired difference ° C (max 10 ° C).

6. Hold down the “FILTER” button for more than 7 seconds and release it by pointing the remote control at the air

conditioning receiver.

3742551750-I-AR-DD.indd 12 11/09/2019 13:41:38

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Argo DD Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Argo DD

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info