Bedienungsanleitung Argo DD (Seite 13 von 16) (Englisch)

724566

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

During the heating mode, the air conditioner will now operate with the new calibration of the air probe.

Nota: this setting has no effect when I Feel is selected. In this case the air conditioner will operate with the remote

control air probe.

ATM mode setting

It is possible to set the air conditioner to operate automatically without a remote control so that it maintains the room

temperature between 18°C and 24°C. A typical application is that of installation within ATMs (cash machine) of banks. In

this mode it is not necessary to set the desired temperature or operating mode, but it will all be managed automatically

by the air conditioner.

To activate this mode, follow the procedure below:

1. Press and hold the “FILTER” button (symbol) for more than 7 seconds. A number will appear on the remote control

screen.

2. Press the + or - keys until the number 11 is displayed.

3. Hold down the “FILTER” button for more than 7 seconds and release it by pointing the remote control at the air

conditioning receiver. An acoustic confirmation of 4 consecutive “beeps” will confirm the successful setting.

Nota: 60 seconds after activating ATM mode the remote control is disabled.

To disable ATM mode, follow the procedure below:

1. Disconnect the power of the air conditioner

2. Wait for 1 minute

3. Re-connect power to the air conditioner

4. Within 60 seconds (before the remote control is disabled again), repeat the procedure above. An acoustic confirmation

of 2 consecutive “beeps” will confirm that the original setting has been reset.

Display setting : Celsius degrees / Fahrenheit degrees

The remote control is set by default to display the temperature expressed in Celsius degrees.

To change the temperature display from Celsius degrees to Fahrenheit degrees (and vice versa), follow the procedure

below:

1. Hold down the “FILTER” button for more than 7 seconds and release it. A number will appear on the remote control

screen.

2. Press the + or - keys until the number 77 is displayed.

3. Hold down the “FILTER” button for more than 7 seconds and release it. The temperature will now be displayed on

the remote control screen with the new setting.

Note: if you remove the batteries from the remote control, the default display is reset.

Factory settings’ reset

To reset the factory settings, follow the procedure below:

1. Hold down the “FILTER” button for more than 7 seconds and release it. A number will appear on the remote control

screen.

2. Press the + or - keys until the number 0 is displayed.

3. Hold down the “FILTER” button for more than 7 seconds and release it by pointing the remote control at the air

conditioning receiver. An acoustic confirmation of 2 consecutive “beeps” will confirm the correct reset of the factory

settings.

Note: to reset the temperature display in Celsius degrees, remove and replace the batteries of the remote control unit.

3742551750-I-AR-DD.indd 13 11/09/2019 13:41:38

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Argo DD Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Argo DD

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info