Bedienungsanleitung Argo ECOLIGHT SINGLE SPLIT (Seite 9 von 41) (Englisch)

724568

Zoom out

Zoom in

Vorherige Seite

1/41

Nächste Seite

V 09/19

 When you select dry mode, the air conditioner will run at low speed in dry mode. The indicator

will illuminate on the display. The fan speed cannot be adjusted in this mode. Pressing the

"SWING" button will allow you to adjust the angle of airflow.

 When you select fan mode, the air conditioner will operate only the fan, blowing air without cooling

or heating. All the indicators will switch off. Press the "FAN" button to adjust the fan speed.

Pressing the "SWING" button will allow you to adjust the angle of airflow.

 When you select heat mode, the air conditioner will run in heat mode. The indicator will

illuminate on the display. Press "▲" or "▼" to adjust the set temperature. Press the "FAN" button

to adjust the fan speed. Pressing the "SWING" button will allow you to adjust the angle of airflow.

N.B.:

To prevent blasts of cold air from being blown into the room, there will be a delay of 1 – 5 minutes

after selecting heat mode before operation begins. (The actual delay will depend on the indoor

ambient temperature).

The temperature can be set between 16 – 30°C and four fan speeds are available: automatic,

low, medium and high.

3. FAN button

Pressing this button will allow you to cycle through and set the fan speed: automatic (AUTO),

low ( ), medium ( ) or high ( ). When turning on the unit, the AUTO ventilation

speed is activated automatically. With automatic speed, the unit automatically selects the fan

speed best suited according to the factory settings. In DRY mode (dehumidification), only the

low ventilation speed can be set.

Note:

The fan speed in dehumidification mode is low.

Pressing the ventilation speed button in Cooling or Dehumidification mode for 2 seconds

activates the X-FAN function and the icon appears on the remote control: the unit will continue

to ventilate for a few minutes, even after the unit is turned off, to dry the battery of the indoor unit,

thus avoiding the formation of mold. This function is not available in Auto, Ventilation or Heating

mode.

If the X-FAN function has been selected: after turning the unit off with the ON / OFF button, the

fan of the indoor unit will continue to run for a few minutes at low speed. During this time press

the FAN button for 2 seconds to stop the fan.

If the X-FAN function is not selected, when the air conditioner is turned off by pressing the ON /

OFF key, the fan switches off together with the unit.

4. ▲/ ▼ button

Press "▲" or "▼" once to increase or decrease the set temperature by 1°C. (The temperature

cannot be adjusted in automatic mode).

When setting the TIMER ON, TIMER OFF, press "▲" or "▼" to adjust the time.

5. SWING button – vertical oscillation

Press this button to set the swing angle (up/down). You can cycle through and set the fan's angle

of airflow as shown below:

nessuna visualizzazione (il deflettore orizzontale si arresta nella

posizione corrente)

no display (the horizontal flap stops in the current position)

nessuna

visualizzazione

(il deflettore orizzontale si arresta

nella posizione corrente)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Argo ECOLIGHT SINGLE SPLIT Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Argo ECOLIGHT SINGLE SPLIT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info