Bedienungsanleitung Argo Einar Plus (Seite 9 von 23) (Englisch)

805048

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

32V 05/23

HOW TO USE THE APPLIANCE

This appliance can be used for Cooling, Heating, Dehumidication and Ventilation. Before using the appliance, leave

it in an upright position for at least two hours.

Plug the power cord into an appropriate power outlet (220-240~V). Insert the batteries into the remote controller,

observing the polarities. Select the desired operating mode from the remote controller.

The air conditioner is equipped with a protection system which causes the unit to activate in Cooling, Dehumidication

and Heating mode only after an interval of approximately 3 minutes from the selection. Even when passing from one

mode to another, the fan continues to operate, but the compressor stops to restart after 3 minutes. This start delay

protects the compressor from overload.

This appliance is equipped with an automatic defrosting system which intervenes when the unit is running hot and ice

forms on the coil. The compressor stops for 10 minutes, after which the appliance resumes normal operation.

THE DRAINAGE TUBE MUST BE CONNECTED to the appliance AT ALL TIMES: the only exception is when the

appliance is used in dehumidication mode only, in which case the appliance should be left to discharge directly

into the room for maximum efciency (see the “Dehumidication Mode” paragraph).

Periodically clean the easily removable air lters located on the side of the product to keep the air conditioning efcient.

1. COOLING MODE (COOL)

• Press the MODE button to select Cooling. The LED on the control panel lights up.

• The temperature adjustment range goes from 16 °C to 32 °C with 1 °C steps.

• In this mode, every time the unit is switched off by pressing the POWER button the appliance stores the set

temperature and when it is switched on again it will keep the setting.

• In cooling mode, the fan speed is high by default, and the temperature present in the room is shown on the

display. Then use the UP/DOWN buttons to select the desired temperature

• In this mode it is possible to adjust the ventilation speed (Speed), set the Timer and activate the Sleep function.

• For quieter operation, reduce speed to low.

2. HEATING MODE (HEAT)

• Press the MODE button to select Heating. The LED on the control panel lights up.

• The temperature adjustment range goes from 16 °C to 32 °C with 1 °C steps.

• In this mode, every time the unit is switched off by pressing the POWER button the appliance stores the set

temperature and when it is switched on again it will keep the setting.

• In heating mode, the fan speed is low by default, and the temperature present in the room is shown on the

display. Then use the UP/DOWN buttons to select the desired temperature

• In this mode it is possible to adjust the ventilation speed (Speed), set the Timer and activate the Sleep function.

• For quieter operation, reduce speed to low.

3. DEHUMIDIFICATION MODE (DRY)

• Press the MODE button to select the Dehumidication mode. The LED on the control panel lights up.

• The temperature is controlled by the electronic board and cannot be adjusted.

Cooling, Heating, Fan Dehumidifying

OPERATING MODES

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Argo Einar Plus Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Argo Einar Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info