Bedienungsanleitung Argo Einar Plus (Seite 10 von 23) (Englisch)

805048

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

33V 05/23

• In this mode, each time the POWER button is pressed the unit switches off, the appliance saves the settings

and retains them when it is switched on again.

• The humidity % adjustment range is 35-80%.

• The fan speed cannot be adjusted.

NOTE: the air conditioner does not cool the room when operating as a dehumidier. When the appliance is

used as a dehumidier, the exible pipe must not be connected. For maximum dehumidication efciency, leave

the rear discharge attachment free to discharge directly into the environment. The dehumidication mode is

recommended during autumn and winter. If used during summer, it is best to leave the exible pipe attached so

that the hot air is discharged towards the outside rather than into the room. During dehumidication, continuous

drainage should be implemented (see the next chapter, “HOW TO ELIMINATE CONDENSATE”).

4. FAN MODE (FAN)

• Press the MODE button to select ventilation until the corresponding icon appears.

• In this mode, the fan speed can be adjusted.

• The temperature cannot be adjusted.

This appliance automatically vaporizes the condensate in cooling mode. When the air conditioner works in Cooling

mode, it is not necessary to have continuous drainage of the condensate; only in particular climatic conditions in which

the humidity rate in the air is very high can water deposit inside the unit.

In Heating mode the condensate is not vaporized automatically, it will therefore be necessary to empty the internal

tank periodically. Alternatively, the drainage can be arranged from the lower hole located on the back of the unit, the

internal condensate drainage will be intermittent.

When the internal tank is full, the air conditioner goes into stand-by mode within about 10 seconds, and the display

will show the message "P1", while the icon will light up on the control panel, signaling that it has been lled.

The buttons on the control panel are not active and the appliance stops working.

The operation LED ring located on the front of the unit lights up red.

To restore the unit, empty the tank.

Cooling and Heating

Make sure that, when the unit works in cooling and heating mode, the rubber closing cap that closes the drain hole

located at the bottom on the back is correctly positioned.

To empty the tank, turn off the air conditioner and unplug it. Remove the cap from the rear drain hole, connect the small

condensate drain tube, which is supplied, and place the other end of the tube above a normal drain.

Make sure the hose is free from twists and bends. The pipe must have a descending trend. Close the drain with the

cap and resume using the air conditioner.

Dehumidication

Warning: when using the air conditioner in dehumidication mode, it is advisable to always set up continuous

drainage to ensure maximum dehumidication efciency. Connect one end of the PVC tubing (provided) to the top

drain hole and the other end above a drain.

HOW TO ELIMINATE CONDENSATE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Argo Einar Plus Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Argo Einar Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info